Unlock and repair x65 v41 series 100% tested

  • Thread starter Thread starter s4sajii
  • Start date Start date
Hi user
i have S65 i change language at update tool with ver 25 after phone die. please help me thank user very much.
 
...got it a explanation off all procedure but on Serbian, so ask hem to translate. I did my part.
Cheers
 
Ok, but if i maked this(apply patch), then i run papuas, when i try to send skey to phone, its will give me factory mode ?
 
This is NOT WORKING for C65 with AMD chip, unless you have PapuaUtils registered.

Anyone has PapuaUtils registered? o:-)
 
Yes,PAPUA TEAM is very big team with 1000 computers and big offices... and only with one man
 
HI Guys,
Was anybody able to unlock a s65v43?? with this solution?

I tried but the testpoints arent working.
can somebody post his own results too

BR Talk
 
im trying your solution but do i need autoignition cable ?without this it is not possible ?
i dont understand exactly your solution. i can find button what u described.
can u post picture please ?
i run PapuaUtils 0.3.3
AutoIgnition...
Boot
 
Do not need tp for older versions(x65 v36 version, at moment TP+ Papuas Soft, is the only FREE solution..
 
I kill this phone with martech and tried this from forum but with papua i get only imei nothing else how I can get bootkey and flashid (esn) it;s amd flash ....and i tried to freez in papua utils but phone is in customer mode and can't do that, ....., when phon eis in service mode i try read codes but iget this
Model: SIEMENS CX7I 50 lg4
Phone is in Service Mode"
IMEI: 354926001854189
SecurityStatus: CustomerMode
HWID: 322
Bttery: 3729 mV.
 
All X65 with AMD flash chip are supported for long time by SST.
Now SST supports also C62 v25-v28
 
Thank you for your reply, therefore you tested x65>36 with sst and dima debil with new TPs and no go?.
 
hi frnd need help abut cx65 only no botton docsnt work but when i on the phon than ok but whn i cal than not cut the line.pls advise me wat can i do?thnx
 
I'm trying to unlock cx70 and at first I made eeprom backup with
Siemens EEPROM tool v3.15
After that I save the eeprom and push Exit button.
Now phone goes off
After that I make TP and with PapuaUtil/Flash.... push Do JOB and that's the message that I get:

AutoIgnition...
Boot not loaded !
Boot unlock .


What did I do wrong?
Bad test point or what?
After I save eeprom, phone goes off, does I need to switch it ON again?

Thanks in advance for any help.

Regards,
Dejan
 
@japunlock: I have tested it with SL65 and CX65 but not with S65... but it seems to work with s65 too
 
i can't open "factory mode" ,
i do this with papua
in flash menu check pause and newbootcore
after that i write skey 8 numbers like 12345678
and flash with martech full flash v43 and after that flash with winswup v50
phone only beep
check in papua in flash mode pause and recalculate keys in flash
and put phone in servise mode
tried freez but it not work cos customer mode
.....
in this ver. phone sw cx70i v43/50, papua (i use v065) can't read esn
i read phone id with martech and put in papua ESN (it is 8 hex nuber, inverted from phone id) and i get hash bkey ihave skey , and i make loader for v klay and map for freia and loader for cx65flasher but i can't boot this phone
if anybody know solution please help
 
Back
Top