QPST USB driver download

Hey all I am trying to hook up my phone to QPST but it only shows COM 1 and 2 there is no USB option. I have read into it and is says you have to have the USB driver for QPST does anyone know where I can download the drivers?
 
Give this a shot:

##DIAG to put your phone into DIAG mode. Once it's in, attach it via USB and take note of which COM port Windows assigns to it. That's the port you'll want to connect to via QPST.
 
I do Have EV in my area. I do not have ##diag on my phone I think I am going to try to find 6800 for sale. It is time to upgrade anyway. Does anyone know someone selling a mogul at a decent price that is flashed to Cricket?
 
I'm sure that it can be done. These guys are good. Wap & mms is already configured in rom s so maybe on day evdo settings will follow. I just can't get qpst to find my phone. With toO's v.3 rom I have everything working for the 1st time, including tomtom. Evdo is the last thing I need.
 
If you don't shop for one that's already flashed to Cricket, you'll save yourself at least $100. You'll have to do the flash job yourself, but odRAB are that the people on these boarRAB can help you flash it better than whatever hole in the wall you may end up buying from.

Your best bet for a low price is to search for bad ESN ones on eBay. I saw brand new ones on there, still in box, for $175 Buy it Now a few weeks back.
 
i have done one mogul in the past that sould not authenticate evdo no matter what i tried...i put all settings in correctly and have worked on that device over 10 times...i have done more than 20 moguls and could find nothing to fix this guys evdo issue...maybe you have one of these moguls that cannot authenticate for some reason.
 
I tried that all and all that I get is an option to add com 3 doesnt have USB and yes I am a noob sorry if the question was stupid just learning thanks for the help guys
 
See I think thats my problem as well. I have had the 1050 prl in for a few months. Didn't know I had to change some settings until last night. I have the Qpst program but it will not recognize my phone. I saw this.

channell nuraber 1709
band class 13
subnet color code 0
uati lotta zeros
uati
6 zeros
active set pilot 255
rx signal 125
rx power -104 dbm
channel per 6753
requested data rate 552.000 kbps
hdr session state 0 = inactive state
date session 0=null
current ip n/a
an/aaa authen. 0= not authenticated



mip default settings
enable profile = enable
nai= [email protected]ntp
mn ha spi set= enable
mn ha spi value = 4d2
mn aaa spi = enable
mn aaa spi value = 4d2
home adress 0.0.0.0
primary ha address 68.28.15.12
sec. ha adress 68.28.31.12
dmu public hey 0
 
Theres a programm called Kyocera SPC tool comes in handy to make a conecction on com1 or com2. You can changed your desire com through Device Manager and also adjust your baudrate most phones speak trhough 115200
 
ya I have the same issue with QPST. I have tried several drivers for the mogul and down to the 6600. None worked. I am going to just give up and buy a mogul and see if I can get evdo on it. This xv6600 is old anyway and it works fine but I want evdo Im greedy LOL. I am going to keep the 6600 and keep playing with it so I can figure it out I dont like to give up. Will keep everyone posted if anything good happens.
 
Well I haven't even tried to set my settings yet. I want to get into qpst to set those settings and then in epst. I get the ev signal alot of my phone then when I go to the internet it goes back to 1x. So I think that my phone will get it, when I get the settings all set.
 
Back
Top