X65 > v36, x70, x75 unlocking - STEP BY STEP!

  • Thread starter Thread starter MR PROTEC
  • Start date Start date
"Connect your phone using DCA-500 or DCA-510 cable (DCA-540 is not supported!)."

is really needed an original siemens cable???
 
I guess your problem is the tolerance of the resistors.

I used some 1/4W resistors and I have had the same problem.

Used 0402 SMD 15k resistors from old 3210 PCB and all was ok
 
My cable also goes wild .... do you have a solution for this problem ?

Does the resistor "trick" work ???

I tried to connect with papuas ... also no chance
 
@eggwisher

Can't you see I wrote >v36?

@UnlockerPT

I didn't mean original cables, but phone has to recognise non-original cable as DCA-500 or DCA-510...
 
Hi mates,

Thanks mikee for testing.

here is the link to the latest x65 flasher(1091) and the above midlet. link

best regards,
Aishur
 
That's not a problem Take cable, plug to phone and start the midlet.
Wait for about 800sec. When it stops working and you'll see codes unplug the
cable and rewrite codes to PU manualy. You have to remember that u're putting HASH without "-" and ESN code turned out with bits, ex. your code is
A1D3-D4F5, you're put it like that: F5D4D3A1.


Greetings
 
Hi mates,
@amir-Skillz
My cables are regular ones based on the Pl 2303 chips (for ultra high speed flashing (driver patch required)) only I added two 10 k resistors with respect to Papua's diagram. Choice Типа DCA-5xx Авто "AT" end for the phone and ignore auto ignition .( Pin 1)
@Crumarix1
If i understood your question. you can find it here.
Best regards,
Aishur
 
@siemensiak.pl
thanks for sharing but steps from 12 to 18 can be replaced by only one step

br
 
@Chris02
for
UNLOCK
SIEMENS C75 v11
without px64v4 and without TestPoint
PapuaUtils v0.7.5c eng

CORECT OR NOT

1. Connect phone using DCA-500 or DCA-510 cable.
(cable c55_15k between 2-5 and 2-7pin)
2. Click
 
@ Aishur

TX for the files.
I uploaded midlet for x75, started, and after 490 ?? he displayed codes.
Cose PU 075 don't read codes from new midlet, I was inputed ( what a english word ) codes manualy,and phone is unlocked ( CF75,v22,lg4 ).

many thanks to all for help !
 
@Aishur
U mean DATA cable....And put Resister as describe in PIC....And where to download the Driver Patch PLZ post here or a LINK
And it will be very Great if u Open ur Cable PINOUT and post Its picture here....I really dont understand that PIC u posted..Never Modified Before..SO Thankx in Advance
 
X65 > v36, x70, x75 unlocking - STEP BY STEP!

When I take the cable (plug in) and start the program it shows the message "please connect accessory" and next moment "please wait" and it goes round again.

I
 
X65 > v36, x70, x75 unlocking - STEP BY STEP!

hi, im using papuas.
my cable works 100% as i can read all codes,
but when i put a sim card into the phone, it says phone code blocked.
and i am not even given a chance to enter any code, it was entered too many times, what can i do to resolve this problem???

it gives me this but phone iss till locked????? ????? ???

IMEI: 354763001395909
SecurityStatus: CustomerMode
HWID: 327
 
Hi mates,
I think you need to go into flash panel and check "recalculate keys in Flash" box (9th box in x65PapuaUtilsV072)
(replace master and replace 76,5008,5009,5077 boxes are self checked too)

and to do jobs

Best regards,
Aishur
 
Back
Top