Unlocking C65 v43 - full solution

  • Thread starter Thread starter pepik
  • Start date Start date
P

pepik

Guest
Unlocking C65 v43 - full free solution in english language,
thanks all for this solution - i
 
@ all thanx,
did 3pcs v41 c65 today.
and no need for resistance between tp & ground , i just bridged a jumper
worked like makkhan (butter).
wbr,
ANUCHOPRA.
 
I can't remember in this moment.
but i think, tp is required only for read ESN and HKEY, when you enter skey in phone, phone must by powered on.
 
patric you don't need tp when you enter skey, only power on the phone before enter skey.
regards
 
--------------------------------------------------------------------------------

I have Siemens EEPROM tool v3.15 cannot be start , it gives unexpected error.
i tried it on win98 and winXP the same error.

I have all these files
msvbvm50.dll
MSCOMM32.OCX
COMCTL32.OCX
comdlg32.ocx

but i dont have mavbvm5.dll

who can help to start this program.??

thanks in addvance
 
hi
i need help, i have six cx65 v41 to unlock, i did it five of them with papautils without problems but the number six give me problems, after i create the log i go to do the map and the mapper tell me, the log size is not correct, i compare it with the other five phone logs and they have 139 bytes an d the number six have 138 bytes, i try once and once more but always i have 138 bytes and size incorrect.
can anybody helps me with this problem?
another question, i have read is posible to unlock the phone if i calculate the nck and is not necessary to input the map, can anybody explain me that?
and finally i have do it the eprom backup with eprom tools before to unlock the phones, how can i do a flash backup? then if i have any problem i can flash the phone.
thanks
 
.
ESN is not iqual to IMEI, ESN a an 8 digit hexadecimal number, when you connect papuas it gives you both, ESN and IMEI.

Papuas give to the log file the name yourimei.log for example 352286259855377.log

Regards
 
Hello to all!

I just unlocked a C65 v43 with this Papua's solution, it is working 100%! BUT I did not have this part when sw slipts out these EEPBlocks 76,5007,5008 and 5077 either ! But now it is unlocked without any problem. So, probably that state depends on our PCs, I guess.

But the solution is A1!
Thanks for the Russian!
 
I can t access to blocks 5008,5009,5077, 5121, 5122 and 5123 in phone.
I think my logs are ok.
In papuas info says block 5123 is missing !!!
But I can t find where s the problem......

Some suggestion ???

See screenshot in attachments

Regards
 
No need to TP when you'll Enter Skey in Phone , just click that button.
If the program stay in "Factory Mode" doesnt matter.
Click Freia Log , save the log after that , open Map Maker , open log , Save Map.
Now it's important.... :
Run Eprom Tool 3.15
Load (button left) , selecet map
Click => buton middle of the program
Select All (from Right)
!!!!!!!!!!!!SAVE SELECTED!!!!!!!!!!!!!
Dont click Save All button

OverAll Success....
 
I have found the solution for this problem as I have exactly the same problem on a SL65.
Use the DOS mapper it work very fine and make correct map without error.
 
Phone is now alive again !!!

Without s4sajii's help..... my phone were now in trash.

ONE MILLION THANKS TO S4sajii

@All

Dont forget to backup the phone !!!
Never forget it !!!

Best Regards
 
You can, but it's not necessary - just use a piece of wire and a sharp pin. Connect one end of the wire to ground (just clip in under one of the screening cans) and wrap the other around the pin.

The hardest thing with this method is getting the timing right - you need to click "DO JOB" and then power up the phone a very short time later. Once the initial bootstrap is loaded, then disconnect the TP.
 
....send to me and I garanty it must work. test point, PapuaUtilits(no mether what Flash IC is inside phone!!!),Eeprom Tools 3.15 by SkyLord(never use "Save all" buton!!!!!!!), MapMakerX65 and that it's.
Cheers
 
Hello sir

i done all steps of given method but at the it not gives "factory mode" it give "Customer mode" so what the problem is there.................................. AutoIgnition...
Transmit Boot...
Boot loaded ...
Pause 2 sec...
Retrieve information...
*Propper work with TP !
Boot unlock .
Calculate KEYS..
Keys calculated good :
BOOTKEY: E96CED26EEC0ECE24D66E00446836763
SKEY: 18035211
Checking entry values.....
Recalculate HASH&BKey from ESN & SKey
New HASH: 2D76B6A3EC72C0E7C86394040643083F
New BOOTKEY: E96CED26EEC0ECE24D66E00446836763
Checking entry values.....
Test ServiceKey...
Enter ServiceKey in phone...
SKey enter !
Pause 8 second(s)...
SecurityStatus: CustomerMode
 
my problem that the phone can connect using tp but when i try to enter sky it gives always error
also the phone can't connect to the eeprom tool

any solution
thx
 
Back
Top