Unlock LG KP500 KP501 all versions

  • Thread starter Thread starter junojin
  • Start date Start date
Phone was detected as turned ON !!! Turn off and try again !
(and maybe in newer Versions letter changed from N,O.... to O=Backup STATIC_EEP; P=Unlock)
 
once installed the drivers,its better to restart ur pc,,,,,
and make sure u type \\.\USB1
and phone without battery.....
if you getting nand read/write errors, ur timing is off,after u write static_eep,just connect cable to pc(do not connect mob)with no batt in mob,press enter,wait 1sec,then plug cable to mob.......(i usually put cable end,just touching,port of mob,then press enter,then push cable into mob)
if you have comport errors,like above,,,then restart your pc.
hope this helps

here all files with instructions,in this folder its called "LG-Utils-0-4-2_Inc_FLP.rar"
"http://rapidshare.com/users/AGDA08"
just delete the ""
 
If any error apeared, it`s only because of drivers. Just use drivers from "allyouneed" and no problems!
 
[x] Flash phone with a unbranded Software Version ( alredy posted in forum LINK )
[x] once finished enter 2945#*71001#
[x] NCK is asked and enter 00000000
[x] Phone Unlocked

Phone must be without sim card.
 
hy guys...

For those who want the phone usb drivers here it goes a fresh new link...enjoy it..

http://rs171.rapidshare.com/files/97495670/LGUSBModemDriver_WHQL_ML_Ver_4_1_.7.zip

BR
 
HI Bro,

Your solution is fully working instead other with full flash who does'nt work on new KP500 version.Thanks so much for sharing coz unlocked in minutes.
Many thanks again.
For others user don't loose time with full flash solution it will not work.
When you want to enter 00000000 it will say Fail unlocking network.
That one is the best.
Fonebloqu
 
Hmm, may be my cable is wrong.
I can't do this: (press enter,wait 1sec,then plug cable to mob....).

Because, program is suddenly ending if not conected phone then have this mesage:

Error during the port openning: Can not delete the non-existing channel 1.

So, I must connect phone without batt and then press enter???

I use USB cable shiped with cookie, this is simple usb without usb to serial adapter...
 
please help me whats wrong with me??

every thing passed well but i get only one file STATIC_EEP.BIG

with the error message:
error during the data receiving: Timeout occured during packet reception

ps:
-i tryed on 2 pcs with USB2.0 but always same resutl
- usb drirver from Allyouneed is tryed too.
 
yes......m8, pls..my LG kp501 is just shows LG LOGO and went off again....now its not automatically detected by pc but when i press power on botton it will detect it....but not install after that detection....

now,what trick do i need to flash it ??????

regards.
 
ahmed nokia
you have the drivers in the forum, i think that this drivers inside are enough http://rs284.rapidshare.com/files/192825035/SETUP_GSMULTI_V30.zip


this solution should work with others LG models, extracting the *.flb file from firmware
 
Yes, yes, yes!!! That's work.

My USB driver has been wrong, my mistake, I'm use driver from "allyouneed", now I can see that's for flashing...

Thanks to all.
 
worked great once i found a good cable (make sure your cable fits corectly) my first cable would not go all the way in look for another cable that fitted corectly and it worked great.
many thanks
 
What exactly have u done?
U nonly needed to readout the EEP.
With this script u can also flash !
 
Back
Top