SL75 Totaly Dead...

  • Thread starter Thread starter LoveLess
  • Start date Start date
L

LoveLess

Guest
hi all..

phoe was working fine.. i tryo change imei.. after steps (given on he forum) phone not power on.. only bip..and now phone is totaly dead..

pls check log...



Getting Information:
Model:SIEMENS SL75 13 lg1
Phone is in "Service Mode" mode
IMEI:000000000000
SecurityStatus:CustomerMode
HWID:411
Accumulator Voltage: 3964 mV
 
...uff,
again IMEI patch...
Open papuautils, go to Flash menu, check only: Pause; ??????OTP and Recalculate Keys. Do the Job and wait. Normarly is neded to put again the OTP IMEI. If not working, remain to use this steps, but with testpoint option.
BTW: your phone need to be OFF (without Service Mode).
dagos
 
imei is correct now.. i have backup...after backup phone is again normally..but again only bip... i think pb is eeprom...cause after writing patched eeprom phone dead..
 
Auto Ignition...
Transfer boot...
BOOT is loaded...
Pause 2 sec...
Getting Information...
FlashID: 0089,880D (64Mb) ...(Intel)
BCORE clean!
OTP ESN: 47A7F043
OTP IMEI: 357017001886152
Not found segment EEFULL!
Working with BCORE...
Phone requires Freeze!?

when i have try to freeze phoene gives error...



Getting Information:
Model: SIEMENS SL75 13 lg1
Phone is in "Service Mode" mode
IMEI: 357017001886152
SecurityStatus: FactoryMode
HWID: 411
Attention: Not matching HWID and Phone model!
Model expected : hw_SL75, but received : SL75 !
Bcore model area is clean !!!
Accumulator Voltage: 3975 mV.
Checking values entered and necessary blocks...
IMEI: 357017001886152
Impossible to get Security information!
 
...don't try to freeze!
Please give to me the actual log file (enter in Service Mode) to see what is happened.
dagos
 
after this flash phone is again bip..and service mode log...

Getting Information:
Model: SIEMENS SL75 24 lg91
Phone is in "Format FFS?" mode
IMEI: 357017001886152
SecurityStatus: CustomerMode
HWID: 411
Attention: Not matching HWID and Phone model!
Model expected : hw_SL75, but received : SL75 !
Accumulator Voltage: 3913 mV.
 
...hmmm,
first, you used fullflash with 64MB (blank)
second, after patch IMEI, you reconfigurate the bootcore area.
Try again to use: "Open papuautils, go to Flash menu, check only: Pause; ??????OTP and Recalculate Keys. Do the Job and wait. " and give me the log file.
dagos
 
...this is old. Use x65flasher-2103. I see now your last post and I'm waiting for this. Your bootcore area is damaged. Remain two posibilities:
- to fullflash with bootcore protection disabled (use MS-DOS prompt and type x65flasher /b). After fullflash your bootcore will be changed and you not connected again to X65flasher. You need to use testpoint unlock with rewriting bootcore (using steps from my last post) with papuautils.
- to fullflash first using X65flasher normarly (without command /b), after you need to write new bootcore (option from papuautils; check only Pause,??????OTP and New Bootcore). After this, in the future you not fullflash or make firmware upgrade. Possible to appair HASH=FFFFFFF...after unlocking.
You have good fullflash file on:
http://rapidshare.com/files/117848701/SL75_470400_160208.rar

dagos
 
Auto Ignition...
Transfer boot...
BOOT is loaded...
Pause 2 sec...
Getting Information...
FlashID: 0089,880D (64Mb) ...(Intel)
BCORE clean!
OTP ESN: 47A7F043
OTP IMEI: 357017001886152
Not found segment EEFULL!
Working with BCORE...
Phone requires Freeze!?
 
sir phone is oki now... after format ffs.. phone is really working fine.. and pls tell me.. imei rebuild is posssible with this phone..?
 
...Ok,
In the future use x65PapuaUtilsV111b.
Which program you used to flash your phone?
 
again bip sir..

FlashID(3) - Manufact. code:0089 (Intel), type: 881C. DisplayID(1,59): Epson L2F50333T.
Checking value of SKEY from page "Codes"...
Auto Ignition...
Transfer boot...
BOOT is loaded...
Pause 2 sec...
Getting Information...
FlashID: 0089,880D (64Mb)
BCORE Cleared!
OTP ESN: 47A7F043
OTP IMEI: 357017001886152
Bcore S/SL75 found
Reading of segment BCORE...
BCORE segment are kept in 47A7F043_A0000000_BCORE_080726160723.bin
Search of a segment EELITE...
Search of a segments EEFULL...
Find blocks: 52,76,5008,5009,5077,5121,5122,5123
In total EEP blocks: 144
EEPROM Blocks saved in .\Backup\47A7F043_EEP_080726160757.eep
Replacement of blocks EEPROM in the buffer ...
EEPROM: Block 76 replaced.
EEPROM: Block 52 replaced.
EEPROM: Block 5122 replaced.
EEPROM: Block 5009 replaced.
EEPROM: Block 5008 replaced.
EEPROM: Block 5077 replaced.
EEPROM: Block 5121 replaced.
New Master codes:
*#0000*12345678#
*#0001*12345678#
*#0002*12345678#
*#0003*12345678#
*#0004*12345678#
*#0005*12345678#
EEPROM: Block 5123 replaced.
BCORE "Cleared", recalculation impossible
Record of the changed blocks in phone...
Write down EEPROM segments...
EEPROM segments write down.
Boot released. Everything is closed.!
 
...after format ffs you loose any settings and data (remain only system files), but is verry good (not neded to fullflash with testpoint). Now your IMEI is real (OTP IMEI)?
Everytime, if bootcere is damaged, I prefered to fullflash with testpoint and unlock after S-Gold phones with Recalculate keys.
Regarding to IMEI patch, I don't like to use this. Maybe working on X65 phones, but on X75 (or X85) phones, no.
dagos
 
yes sir... imei is otp imei...and now i will try again.. but at first i have to change phone's lang.. phone is Russian now.. how can i change it..
 
I suppouse to use DCA510cable (workinkg with flash/firmware upgrade):
-go to http://eh.student.utwente.nl/~landy/index.php?dir=SL75_SL75C/
user: mobile
password: elibom
and download firmware with your language country (see on attachement for languages).
Open executable, set com port and go!
I propouse to make backup from your phone first (fullflash), because if your bootcore is not real for SL75 and is possible to crash the firmware upgrade and you need to fullflash again....
dagos
 
Back
Top