Siemes A55 Flash Problem

  • Thread starter Thread starter imran_qasim
  • Start date Start date
I

imran_qasim

Guest
when i try to flash siemens A55 with Freia and fls file it shows the following error
COMM_LoadBoots : selected phone family is 8
TTY_OpenCOMPort : opening COM1
COMM_IsBootRunning : bootcode does not seem to be running
COMM_LoadBoots : Waiting to power on the phone ...
COMM_LoadBoots : phone is powered on
COMM_SendBoot : boot file is not accepted

and when i use it with SST it showing that
Bad Communication

what is the problem can any one help me out???
 
For what you flash a55 by FREIA? Phone is dead or what??? you can't flash by SWUP?
If you want flash by FREIA you must cut testpoint, but remember if you cut TP you can't flash by SWUP

br.
fingusio
 
@nabil2000
i've two flash files and tried both of it but same error and i am newbie dont know much about internal hardware to create test point but can you show me the picture for testpoints so i will do the sam

SIEMENS A55 LG1 V11 - 00800000.FLS
SIEMENS A55 LG1 V9 - 00800000.FLS

thnx
 
phone was mistakenly droped by me on the road and when i pick it up and try to power on, then its just flash the screen with orange light and then turned off, someone told me that its software problem just flash it so i try it with two flash files as i mentioned earlier but nothing its still showing errors
tc
 
Its doesnt show any error just flash the scree once and then turned off, it is done every time wheneve i press power button, and when i try to flash with flash file it says Boot file not accepted with freia and says bad communication with SST v5.38
thnx all of you for you reply
 
If you have "Boot file not accepted" thats mean that you must make TP.
I think do you know that you must change in Freia in Configuration functions Boot type to Bootcore Bug.

Make TP and just try flash, if you flash and problem dont disapear try find eeprom and write, if problem still disapear this is HW problem.

That's I think....

br.
fingusio
 
i hace the same problem , but i did't drop it ... my phone shows Wrong Software error ... please give full info , and the downloads i need to make to put it online again ... 10x in advance
 
You are wrong, mate! If you cut the testpoint, you still can flash the phone with SWUP, but phone must be powered on.
But you are right: if phone is dead and the owner in a newbie, he must first try the SWUP solution.
 
It is 100% hardware!
That friend who told it is software could go to sell tomatoes and cucumbers in the market!
Logicaly, if you dropped the phone on the ground, what happened with the data from the flash? Just dissapeared?
If the content of a flash IC just dissapear when it's dropped, it means you can fix it by software! But I don't think so!
The only one working solution is:
1.Rehot the CPU, and move it VERY carrefully, just a little bit!
2.Rehot the flash IC, and move it a little bit.
3.Rehot the RAM IC, move it just a little bit.
4.Make the testpoint
5. Flash it with Freia {Firmware and Eeprom area) or with Joker (Full Flash)
6. Unlock the phone (with freia it will be the best)
That's all!
P.S.: Usually only the CPU is damaged first in A55, so you can try first ny skipping step 2 and 3 first. If not working, then rehot the flash and RAM, and try to flash again!
 
You are 100 % right, but after these steps if phone dont work, probably problem is in flash IC (cut off pin or pad) - change it and then flash again
 
If the rehot solution not work, FlashIC and CPU must be desolderet, and reballed! When I am sure I soldered well the flash, CPU, Ram and Dialog, I can go to computer and make a Full Flash.
If the flasher give me any error, one or more Ic's are damaged, so I change the IC's.
Usualy the Flash IC, or CPu, and sometimes the RAM, but depends on what error was given by the flasher.
Joker 0.3.4.3 is the best flasher for E-gold until now, because is fast and has a complete error reporting!
 
Back
Top