Siemens EEPROM Tool killed my SL45

  • Thread starter Thread starter itz_faraz
  • Start date Start date
I

itz_faraz

Guest
Hello

I was just trying to see what EEPROM tool does. I just ran the program, pressed INIT and inserted my mobile into the station (powered off). And then I think I pressed the Load All button.

I wanted to backup my EEPROM before I could have some fun with V_Klay, so I clicked Select All and copied all the blocks to the left list and pressed the Save button. I think it saved all the blocks into a file (which I specified). I didnt do anything else. I dont remember If I pressed Exit but I think I did. And then I took my mobile out of the station.

.. now it doesnt turn on. Is it gone for sure ? I have the Siemens EEPROM Tool, Unisiemens, V_Klay and the v56 firmware. How can I repair this ?

Faraz Azhar
 
You made a mistake.
You propably deleted your EEprom from Phone. (Button Save in right side or left side)?? If right - you vanished your EEprom.
You must apply new EEprom.
Copy of your EEprom can You do f.e thanks to Siemens Flash Tools.

New eeprom can You download f.e from here: http://www.siemenssl45i.gsmhosting.net/modules.php?name=Downloads&d_op=getit&lid=29

Use Siemens Flash Tools(for example) there you choose write EEprom, Sl45 and your Com, and then press Read File-choose your EEprom location and write new EEprom.

Regards.
 
Yes I pressed the left and the right save buttons both. (I dont know why :S ).

But if I run the EEPROM Tool program again, it loads and displays the EEPROM in the list (by clicking Load All) all ok. So does it mean that EEPROM isnt deleted?

However I think the block values are all changed. There is no 67 block (which is for battery). It was there before I pressed the Save button. Now all the blocks are listed from 5000+ series.

I downloaded the file you specified. It looks to be V_Klay's BIN file. Can V_Klay be used with it? Can Unisiemens be of any use?
 
Im trying Unisiemens right now.. I opened it, clicked Read EEPROM.. it read it to full 100%, then I loaded the eeprom file from Open File, then I clicked Write EEPROM. It says "Flashing" and shows "0%". Its stuck there.. not moving ahead from 0%. How long does it normally take to flash? Its been 5+ minutes its stuck at 0%.

PS. Does this program show whether a file is loaded or not? And do I have do set any values in the 'From' and 'Size' fields?
 
@ itz_faraz

Very brave, but stupid to use EEPROM Tool to see what it`s doing

Are u sure you are running cracked UNIsiemens exe ? ..or tryin to see what original will do ?

So there must be 2 exe-s in UNIsiemens directory, one original (with icon), second crack (without icon) ...

So you have to use second one ...and press power button afterwards u press "write flash/eeprom"


Regards,
BeQuA
 
@BB-gsm
It worked once I took out the mobile, took out the battery for a while & put it back again and tried all over again. It flashed ok

I flashed with the eeprom file. Now my mobile turns on for a while, ie. the back light turns on, then it says "Wrong Software" and goes off again. What now?

I tried reinstalling the v56 firmware, but it made no difference.
 
@ itz_faraz

Write this eeprom ...

And then Direct unlock it with FREIA !


Regards,
BeQuA
 
Ok ill give this a try as well. Where to get FREIA from?

And what is this procedure supposed to do?
 
Back
Top