Siemens A60, C60, etc BZZZZZ on power

  • Thread starter Thread starter moder10
  • Start date Start date
Now mobile works.

For the language, there's not ITALIAN...how can i do?
Many thanks to all

Br, Moder
 
...and if you try to flash (using Joker) your phone using other flash capacity, you will see one message:
Soft FlashID: 0001/220C
FlashID: 0089/8856
.............................
Warning: The software of the telephone does not correspond to FlashID!

dagos
 
...X55data cable (serial cable) is used for the firmware upgrade and file transfer between PC and mobile phone.
C55 serial cable (service cable) is used for flashing/unlocking Siemens E-Gold phones (and somme S-Gold phones).
Diferences:
C55 use RX;TX;GND connection
X55 use RX;TX;GND;DCD;RTS connection
dagos
 
...THIS IS THE SIEMENS C55 PHONE!!!
Use the cable for this (marked on the RS232 female connector "For SIM C55") or DCA500 serial cable.
dagos
 
REHEAT??? how???
You're joking

if you're serious, write me how to do, so i try to make it quickly.



Mobile now work (i have made a call to customer service), but the display is all BLU....there's a way to resolve it?

I've tried to make DEFRAG EEP and DEL INSTANCES, but without success.

It happens this for DEFRAG EEP :

Backup EEPROM blocks...
No Ping mobile
Backup EEPROM blocks...
No Ping mobile
Backup EEPROM blocks...
HWID: 132 (MC60)
EELITE Info: free buffer 55592 bytes, free at all 55624 bytes, free for deleted 55624 bytes.
EEFULL Info: free buffer 84762 bytes, free at all 86484 bytes, free for deleted 21092 bytes.
Read All EELITE blocks from 1 to 285 ...
 
Yes,and use freia...it's easyest

du u open an oldsiemensService,or u discower a siemens factory garbage ????
 
...Ok, to understood:
-enter in service mode and send to me log file.
-try to set your contrast (if have low level, your color display is blue).
Goto the Contrast Tab in Joker -> Enter service mode ->Light on -> 5007 -> Read -> Adjust contrast -> 5007 Write
- try to change your display (is the same with C60)....
Is possible to have bad contact or missing connection between the phone microcontroller and display connector. Try to rehot the microcontroller BGA (using the hot air generator). Manny times here is the problem (on the Siemens phones - bad connection between the PCB pads and microcontroller).
dagos
 
did u try Contast tool for Siemens,usualy after flash u need to setup contrast level...


and yes u need to do CUT...


du u ewer read old post before u posting ???
 
ALL ok.

Mobile now work, but...usually the language...no italian.

The files are:

A62C_070800_xbz.zip 12 4.8 MB 2006-Apr-16
A62_060100_service.zip 10 4.5 MB 2005-Apr-12
A62_069500_service.zip 12 4.3 MB 2005-Apr-12
A62_070100_service.zip 18 4.4 MB 2006-Dec-04
A62_070200_service.zip 5 4.4 MB 2006-Dec-04
A62_070300_service.zip 5 4.4 MB 2006-Dec-04
A62_070400_service.zip 10 4.4 MB 2006-Dec-04
A62_070500_service.zip 13 4.4 MB 2006-Dec-04
A62_070600_service.zip 9 4.4 MB 2006-Dec-04
A62_070700_service.zip 4 4.4 MB 2006-Dec-04
A62_079000_service.zip 4 4.4 MB 2006-Dec-04
A62_079100_service.zip 137 4.4 MB 2006-Dec-04
A62_079200_xbz.zip 272 4.3 MB 2006-Apr-16
A62_079800_xbz.zip

According what said , the A62_079800...means:
A62...mobile
07...firmware
98...????
00...language pack (01...is not present??)

Br,
Moder
 
May i know the cut for siemens a60...where is?
Many thanks


Using FREIA...without cut.........this is the log:

FREIA - Engine build 10, Frontend build 9
Thanks goes out for the following:
Maxim, Rolis, Sergey, PapaJoe, Lead,
TheWizard, Jozso (for hardware and cable
support and of course beta testing),
Nico, Victor, Pinker, Tom,
and all the others who supports ...
COMM_LoadBoots : selected phone family is 13
TTY_OpenCOMPort : opening COM1
COMM_IsBootRunning : bootcode does not seem to be running
COMM_LoadBoots : Waiting to power on the phone ...
COMM_LoadBoots : phone is powered on
COMM_SendBoot : boot file is not accepted


Moder
 
Hi dagos,
i specify that each time i make something on the mobile, it makes BZZZZ.
Said this, these following are the logs regarding each point you request:

SERVICE MODE:
Start...
Loading ServiceBoot...
Sending ServiceBoot Ok.
MobileMode: Service
HWID: 132 (MC60)
MC60 lg95 Sw05 17.09.03 12:23:47
IMEI: ************
DisplayID: 34, Sharp Hynix HM17CM4101
FSN: 26655A03
SW FlashID: 0001/2212
Code(05): OTP closed
Code(09): BootKEY is written in EEPROM
Code(0D): Keys are registered in BCORE
Code(13): Complete access to BFB
Code(15): Complete condition
Code(19): Monitoring is switched on
Code(1D): Blocks 5121,5122,5123 are present
Battery Voltage 3776 mV.
SecurityMode: Factory

THE CONTRAST:
this is the value
44,48,0,0

When i try to read it makes BZZZ, and after several times the result and the new settings:
Read Contrast...
No Ping mobile
Read Contrast...
No Ping mobile
Read Contrast...
Display1 contrast: 44, 48
Display2 contrast: 0, 0
Test Contrast 94...
No Ping mobile
Test Contrast 94...
No Ping mobile
Test Contrast 94...
Write contrast (94, 95) in block 5007...
Write block 5007 - Ok.
Display1 contrast: 94, 94
Display2 contrast: 95, 95


After this, the mobiles work, but DISPLAY is always "Blu"


Br, Moder
 
I have the cable "For SIM C55" and port rs232.....infact when i try to read, appear that message on Joker.

Moder
 
Hi guys,
when i try to turn on the mobiles SIEMENS A62, the mobile make "bzzzzz" and than turn off automatically.

I know, i've to do the FULLFLASH, but after downloading files, i watched that some are for 8mb and other for 16mb.
So....how can i unsterstand if i need the ff for 8mb instead of 16mb?

I have these files:
A62_16MB_Repair_FF.rar
a62_full_0604.rar
a62_v06.rar
A62v07_8MB_Repair_FF.rar
which is the file i must use???


Br, Moder
PS:::: this is the log of mobile

SERVICE MODE
Start...
Loading ServiceBoot...
Sending ServiceBoot Ok.
MobileMode: Service
HWID: 231 (A62)
A62 lg98 Sw07 16.05.05 15:08:56
IMEI: ******************
DisplayID: 37, Philips Epson S1D15G14
FSN: 3944D507
SW FlashID: 0001/220C
Code(05): OTP closed
Code(09): BootKEY is written in EEPROM
Code(0D): Keys are registered in BCORE
Code(13): Complete access to BFB
Code(15): Complete condition
Code(19): Monitoring is switched on
Code(1D): Blocks 5121,5122,5123 are present
Battery Voltage 3780 mV.
SecurityMode: Factory

DEL INSTANCES
Instance Format...
Delete Instance "Voice Memo" - None.
Delete Instance "Voice Dialing" - None.
Delete Instance "Browser Cache" - None.
Delete Instance "File System" - Ok.
Delete Instance "Tegic" - None.
Delete Instance "Address Book" - Ok.
ReStart Phone!
Instance Format...
Delete Instance "Voice Memo" - None.
Delete Instance "Voice Dialing" - None.
Delete Instance "Browser Cache" - None.
Delete Instance "File System" - Ok.
Delete Instance "Tegic" - None.
Delete Instance "Address Book" - Ok.
ReStart Phone!

DEFRAG EEP
Backup EEPROM blocks...
HWID: 231 (A62)
EELITE Info: free buffer 55540 bytes, free at all 55572 bytes, free for deleted 55572 bytes.
EEFULL Info: free buffer 87012 bytes, free at all 87224 bytes, free for deleted 21832 bytes.
Read All EELITE blocks from 1 to 285 ...
Read All EEFULL blocks from 5000 to 5439 ...
 
Back
Top