Samsung Z107 UNLOCK SOLLUTION FREE

[kega234]

thanks rfor that goood job

 

[gsmlab4u]

if u dont mind pls send me z105 unlocking sw.

gsmlab4u

 

[forhike]

hello!

this works on z105 and z107
use same instructions =)

 

[drdjolens]

Nice work.

Thx.

 

[Nemooo]

Gone crazy?

I just translated the procedure posted by forhike for alamedin b/c he asked for a link of a german translation.

 

[forhike]

hello! wats wrong with the link above ? =)

just press the link

 

[TRIBULUSS]

If you are locking for samung z107 unlock sollution, why don't you just try with same program that you have when unlocking a z105?

simple use. com connector and short tx and rx pin 2-3 on the (com)
use samsung original usb cable PCB157ULE

I HAVE SAM Z107 AND INSTAL SOVTVER AND DRAIVER IS OK.AI HAVE ORIGINAL CABLE FOR SAM 107.IF I VANT UNLOC PROGRAM WRITE...START UNLOCK,CHECK SERIAL COMUNIKACION WITH THE FONE,SERIAL COM - NG

THIS IS ALL
WHAT MUST AM DO IT::?????

WHAT IS IT Short tx and rx pin 2-3 o ---_??????

 

[ReviveR]

Non-English posts are not allowed in any form here, sorry.









BR

 

[GSM MIND]

me try to make this cable and hope it will work for me


REGARDS

GSM MIND
STAND ALONE

 

[iserlohn]

You don't need to special cable, just put a wire to short out pin 2 and 3 on your serial port. Then use your USB cable to flash.

 

[joe2517]

i have a p107 & x426 samsung cell locked can some help me please

 

[forhike]

you have to use a com connector and short (connect pin 2-3) tx and rx)
that will make it all happend =)

you can for example take the connector from a old com mouse or anything like that.

 

[Myco1GSM]

Hi all

ALL UNDERSTOOD WELL & clear

USB Cable made
Fone found
Modem on COM 5
but i dont have serial port

program looks for COM than stops with error

P.S. when modem on COM-5 & run the program i get "cant open COM-1" error.

Any Ideas, please

Thanks 1000 X in advance

 

[byteforce]

Referring to the z105cable.rar there is this pinout:
USB Connector S100 Connector

1 GND(black)----------------- 5
2 D1 (green)---------------- 18
3 D0 (white)---------------- 16
4 +5V (red)----------------- 19

I have connected correctly according to this pinout, but I have no luck.
While on another tutorial that I found on the web named: "z105 detailed phone freeze remove tutorial" there is told that you must use the s100 connector, and we all know that S100 has a completely different pinout from that above mentioned by me.
Any advice would be appreciated.

 

[byteforce]

So nobody has an idea? To help me?

 

[joe2517]

can u unlock a sgh-p107 or sgh-x426 samsung network locked

 

[tele-teknik]

Nice work.

Thanks.............

 

[iserlohn]

No need to make the cable. Just use the original USB cale, and then make an adapter that short out pins 2 and 3 on your COM1. (You can just use a piece of wire to do this)

The software only checks the carrier on the COM port, and then it uses the USB serial port to do the unlock.

 

[forhike]

use s100 connector and soldier it acording to the z105 pinout and it will work

 

[pyroz]

I need modem driver for Z107v
Z105 drivers dont work

br,
pyroz