A
amacedo
Guest
Hi, i have a S65 dead, i have tryed almost anything, last i try was the AllBugSGold but papuas say "Boot not loaded" then "Boot unlock" and that's all. Please, any help???
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
D
Dave.W
Guest
Try SST-GSM cracked 5.31
Post results
Post results
A
amacedo
Guest
My phone do not ON, when i press the ON button just hear a BIP, SST 6.50 say Satarting Service Mode and that's all.
HELP
HELP
D
dagos
Guest
Hi,
Try to use the C55 datacable and try to flash your phone with the good fullflash file (using X65 flasher and TP option). If boot not accepted, your bootcore area is damaged. Only with Martech box you repair bootcore failure.
Br,
dagos
Try to use the C55 datacable and try to flash your phone with the good fullflash file (using X65 flasher and TP option). If boot not accepted, your bootcore area is damaged. Only with Martech box you repair bootcore failure.
Br,
dagos
A
amacedo
Guest
I guess there must to be another way, i guess the bootcore area is damaged cause papuas say "Boot not loaded" when i try to use papuas, I have been tryed with winsfwup, checking SKIP and trying to flash a full flash, but winswup say "Cannot conect with phone with boostrap on Com6", any idea??
D
dagos
Guest
...using WinSwup, you don't make fullflash on your phone, only the firmware upgrade/downgrade. Try to make fullflash with X65 flasher and download good fullflash file.
dagos
dagos
C
cavi
Guest
i need your help about this one dagos, i did clear bootcore with s65 coz it was hanging but now phone can not turn on. waht should i do now and waht is the best flash file to use?
D
dagos
Guest
...in your case you need to try first to repair bootcore. If not working, fullflash your phone using testpoint procedure and after unlock it using papuautils...
See bellow what I writed in the one from my posts:
...use X65Flasher software, testpoint options and fullflash file from http://rapidshare.com/files/141368814/S65.rar.html
Open x65flasher software using MS-DOS command: x65flasher /b
(write included bootcore).Select testpoint option, connect testpoint, click on the "Connect" button, disconnect testpoint and wait to flash your phone. After is finished, close X65Flasher and open: Papuautils -> Flash -> check "????? OTP", Recalculate keys (all options) and Pause -> Do the Job -> connect testpoint -> push shortly the power button and wait ...
Anyway, try first to repair bootcore area using Papuautils (with presented steps) and after (if not working) fullflash your phone.
dagos
See bellow what I writed in the one from my posts:
...use X65Flasher software, testpoint options and fullflash file from http://rapidshare.com/files/141368814/S65.rar.html
Open x65flasher software using MS-DOS command: x65flasher /b
(write included bootcore).Select testpoint option, connect testpoint, click on the "Connect" button, disconnect testpoint and wait to flash your phone. After is finished, close X65Flasher and open: Papuautils -> Flash -> check "????? OTP", Recalculate keys (all options) and Pause -> Do the Job -> connect testpoint -> push shortly the power button and wait ...
Anyway, try first to repair bootcore area using Papuautils (with presented steps) and after (if not working) fullflash your phone.
dagos
G
g-gabber
Guest
I think, your bootcore is dameged, so there is one way to repair it.
Desolder the flash chip, connect it to a pronomer. And write a good bootcore.
Desolder the flash chip, connect it to a pronomer. And write a good bootcore.
D
dagos
Guest
..if bootcore is damaged, not needed to desolder the flash chip. Just flash bootcore (fullflash files include the bootcore part) using testpoint and X65Flasher software. This methode is tested and working to manny, manny times and most persones use this methode.
The phone starting instructions is writed in the CPU, not in the flash
dagos
The phone starting instructions is writed in the CPU, not in the flash
dagos
A
Aymen G
Guest
please more detail about s65 testpoint !
thx !
thx !
D
dagos
Guest
...in this morning I writed my response, but not saved...
To flash your phone with bootcore, you need to make the following steps:
-open X65Flasher with MS-DOS command "x65flasher /b"
-connect testpoint (solder only one diode pin and touch with the seccond the testpoint pad). See on attachemment for the testpoint pads.
-connect shortly two pins on the keyboard/LED connector to start phone, see on attachemment - marked in red line (if you have the cable with autoignition, not needed).
-disconnect testpoint (see message on the flasher window). You have three secconds to disconect it.
-click on "Write Flash" and select your fullflash file.
-wait to finised...
After fullflash, you need to unlock your phone. In your case (with the bootcore from the other phone, you need to make the following steps:
- open X65Papuautils (version 1.1.1b or c) and go to the "Codes" menu.
- if you know SKEY from your phone, write here, if not, write 12345678 .
- go to "Flash" menu and check only "Pause", "?????? OTP" and from Recalculate keys all options (if check "in Flash" automatically is cheched the all options from this...).
- connect testpoint.
- connect shortly two pins on the keyboard/LED connector to start phone (if you have the cable with autoignition, not needed).
-disconnect testpoint (see message on the flasher window). You have three secconds to disconect it.
-wait to finish.
Now your phone is unlocked...
dagos
To flash your phone with bootcore, you need to make the following steps:
-open X65Flasher with MS-DOS command "x65flasher /b"
-connect testpoint (solder only one diode pin and touch with the seccond the testpoint pad). See on attachemment for the testpoint pads.
-connect shortly two pins on the keyboard/LED connector to start phone, see on attachemment - marked in red line (if you have the cable with autoignition, not needed).
-disconnect testpoint (see message on the flasher window). You have three secconds to disconect it.
-click on "Write Flash" and select your fullflash file.
-wait to finised...
After fullflash, you need to unlock your phone. In your case (with the bootcore from the other phone, you need to make the following steps:
- open X65Papuautils (version 1.1.1b or c) and go to the "Codes" menu.
- if you know SKEY from your phone, write here, if not, write 12345678 .
- go to "Flash" menu and check only "Pause", "?????? OTP" and from Recalculate keys all options (if check "in Flash" automatically is cheched the all options from this...).
- connect testpoint.
- connect shortly two pins on the keyboard/LED connector to start phone (if you have the cable with autoignition, not needed).
-disconnect testpoint (see message on the flasher window). You have three secconds to disconect it.
-wait to finish.
Now your phone is unlocked...
dagos