Reviving 1 dead SL75, now 2

  • Thread starter Thread starter warmsteel
  • Start date Start date
W

warmsteel

Guest
Hello to you all

I was attempting to revive an SL75 that had a start problem. The phone just beeped when the power button was pressed.
I had a working SL75, that when following this thread http:///vbb/showthread.php?t=277159&highlight=dead+xx65-xx75 I inadvertently killed @&%$, my working SL75. I was saving the eep files when I pressed the save all button thinking I had swapped phones! Now I have two phones that just beep.

I have searched the forum before asking anyone for help and I followed the above thread exactly but I can never get past step 7? Perhaps the eep file that I saved is corrupt or it is of the type?
I then tried Video Help for repair All Soft Bug SGOLD platformgetting all the way to the WinSwup only to find that I got an error message
 
Hi,
first try to make the FW 39 firmware upgrade. Set comm and baudrate to 115200 Kb. After check "Skip" on "Pre-check" case. Click on "Start" and press shortly red key from the phone and wait to the firmware upgrade (or downgrade) is finished.
Try now to start the phone.If not, write eeprom file from attachemment using eeprom tools.
If dont't started, remain to make the fullflash using X65 flasher.
For the firmware file, download from: http://eh.student.utwente.nl/~landy/index.php?dir=SL75_SL75C/

user: mobile
password: elibom

For the fullflash file, download from: http://rapidshare.com/files/60589361/SL75_full.rar

Br,
dagos
 
Following your suggestion, these are the results that I have obtained!

Phone 1: Phone I attempted to repair using working phone
Phone 2: Phone I killed trying to repair phone 1

Phone 1

First Method
Connected phone to serial cable, set to com 1 and 115200 kb, upgrade process began using SL75390300.xbz_service.exe. Waited till the end and disconnected the phone. Pressing the on button the phone did nothing but beep?

Second Method
Placed phone in service mode with Papua utils v079e, closed Papua utils then opened Eeprom tools v3.15. Read eep file and checked phone then pressed write all,
 
... yes, writing by EEPROM tools all blocks, you damaged the bootcore area. Try to write fullflash using X65 flasher (and protect bootcore). If don't working, remain to repair your phone using Martech testbox. About the only beep from your phone, use papuautils, enter in service mode and place your log file here to be readed.
Br,
dagos
 
Hello Dagos and BouRRi

Firstly thank you very much for your help so far, it is much appreciated.

Ok, I have rewritten the Eeprom files to the phones but as before I get the same errors where blocks 5008,5009,5077,5121,5122,5123 can not be written to the phone? I had to press ignore to continue.
When I tried to switch the phone on again it just beeped!

I wrote the full flash you gave me to the phone using x65 flasher, all went well but still the phone will not switch on, it just keeps beeping at me.

I did this procedure with both phones. Unfortunately I do not have a Martech testbox so I am a little stuck with that one!
I did however find this http://forum.allsiemens.com/viewtopic.php?t=4987 but it appears to be in Russian. I have attempted to translate it but it does not make sense.

Here are the service logs for both phones

phone 1

Boot in "Service mode"...
Press RED key (Power ON)!
Auto Ignition...
Attention: For the new "S"75 work is done in Beta mode!
Transfer boot...
Boot in "Service mode" Ok
Awaiting Power On phone...
Getting Information:
Model: SIEMENS SL75 24 lg91
Phone is in "Format FFS?" mode
IMEI: 357017002110685
SecurityStatus: CustomerMode
HWID: 411
Accumulator Voltage: 3755 mV.
SimSim activated
EELITE Info:
Free buffer 81412 bytes, free at all 105164 bytes, free for deleted 105164 bytes.
EEFULL Info:
Free buffer 40182 bytes, free at all 221240 bytes, free for deleted 90200 bytes.
MAP info:
Date: 20/01/06, Variant: A 910,
Std-Map/SW: 1/24, D-Map/Prov.: 12/176
To Get Extended Info - Enter Skey into the phone!
Phone operated: 670825 sec.
Total Talk time: 18531 sec.
FlashID(1) - Manufact. code: 0089 (Intel), type: 880D,
FlashID(2) - Manufact. code: 0089 (Intel), type: 8819,
FlashID(3) - Manufact. code: 0089 (Intel), type: 881C.
DisplayID(1,59): Epson L2F50333T.

phone 2

Boot in "Service mode"...
Press RED key (Power ON)!
Auto Ignition...
Attention: For the new "S"75 work is done in Beta mode!
Transfer boot...
Boot in "Service mode" Ok
Awaiting Power On phone...
Getting Information:
Model: SIEMENS SL75 39 lg3
Phone is in "Format FFS?" mode
IMEI: 000000000000000
SecurityStatus: CustomerMode
HWID: 411
Accumulator Voltage: 3738 mV.
SimSim activated
EELITE Info:
Free buffer 105164 bytes, free at all 105164 bytes, free for deleted 105164 bytes.
EEFULL Info:
Free buffer 36667 bytes, free at all 221392 bytes, free for deleted 90352 bytes.
MAP info:
Date: 16/12/05, Variant: A 911,
Std-Map/SW: 1/24, D-Map/Prov.: 12/176
To Get Extended Info - Enter Skey into the phone!
Phone operated: 74 sec.
Total Talk time: 0 sec.
FlashID(1) - Manufact. code: 0089 (Intel), type: 880D,
FlashID(2) - Manufact. code: 0089 (Intel), type: 8819,
FlashID(3) - Manufact. code: 0089 (Intel), type: 881C.
DisplayID(1,59): Epson L2F50333T.


Thank you once again

Warmsteel
 
Back
Top