New.CF62 Testpoint for cutting!!!

  • Thread starter Thread starter evan_silbert
  • Start date Start date
PLs load this full 14M, using freaia to flash and unlock cos with 16M full, you need SST:

http://support.gsm.com.vn/anhtam/CF62_v84_lg95_00200000.zip
 
now that there is a test point for cf62. what is the procedure to unlock t62t t-mobile? does the phone still need to be flashed with v7 firmware? or can phone can be unlock without flashing?
 
Since this is a tricky TP to cut, and we know by now that there is a direct line from simcard reader pin 6 to CPU ball U15, and that the simcard pin 6 line passes rigth under the TP line. I thought-up a method to maybe lessen the risk, of cutting the simcard-reader line and avoid the "insert sim card" problem. See attached.
 
before unlocking ,i took its backup in patched Freia by Seba..
then i unlock it,shows OK,
but after that phone says INSERT SIM having sim inside..
i upload v7 flash 12mb,eeprom256kb,and boot 2 mb in it
phone gets dead
then again i flashed it with backup..still dead,
then i flashed it with repair flash V7 14mb..phone gets ON but no display
i suuccessfully set contrast at last with SST TOOLBOX 4.81
now phone is ON,but again with INSERT SIM ,having sim inside,
any solution for this ??




Raman
icq 167901740
[email protected]
 
must read all posts
i wrote that i test this solution and work 10000000000000000000%
i make mistake before cuting.
ONCE AGAIN 100%

someone read eeprom ver 11 and send me please
[email protected]

thanx
 
Hot AIR in america means "Loud and confused and empty talk" meaninglessness, nonsense. Donot cut or do anything untill you get more information. If this is a false statment that person be should be barred.

If in doubt look-up in a american dictionary "hot air"
 
I also have "insert sim card" with card in phone.
Which SW you use for flash with 14mb flash file?

Regards
 
has anyone tried grounding the TP instead of cutting???

i'd try but don't got a cf62 on me
 
so we cut this small resister??? remove it??? ground it???

then we use friea set to m55???
 
...cut TP and solve that. For more information look in http://forum.gsmhosting.com/vbb/showthread.php?t=169603
Cheers.
 
The problem is after many people have looked at the CF62 diagrams and TPs there is no way get to the unlock TP only by cutting TP can the new CF62 v11 and up be unlocked.

http://forum.gsmhosting.com/vbb/showpost.php?p=914719&postcount=70
 
Hi folks,

Hope this picture helps out, I have also added to my collection at http://people.itu.int/~emartine/

PS
Bulba, I take back everything I said about you great work thanks.
 
Fellows, this is getting scary. Is the problem with the CF62t, or CF62 verison xx I am getting a little lost here. Has anyone fully unlock a CF62 verison X or CF62t using the new testpoint, and what software was used? Before we can fix or find the problem lets narrow it down to what is working and to what is not working, any side effects after the unlock like "insert sim card". Lets not have a CF62 massacre in our hands....
 
To unlock the new CF62 you need to carefully cut test TP. You can see TP at http://people.itu.int/~emartine/Testpoints.htm see CF62 Testpoint and also see Testpoint Cutting method

Good luck
 
@ednacell
Sounds like a good idea. Might be worth a shot. Thanks for posting it here.

@fuzionGSM
This TP can't be grounded because:
A) it's below the surface
B) the idea is to cut off the transmission to t9 which is why you cut it

Someone correct me if this is wrong...
 
thx ednacell
much clearer

so just take like a pin and scratch out the connection???

never done cut method before
 
Back
Top