MC60 v7 Help please - its the bzzzz again !!

  • Thread starter Thread starter Seedy
  • Start date Start date
S

Seedy

Guest
Ok just like any other fone checked version of this MC60 and it was v7, so used freia 15 and selected MC60 and unlocked - procedure went fine. I then switxhed on fone and then blank screen and bzzzzzzzzzzz and the turns off !!!

Does anybody know how i can solve this - the fone was 100% working before

Any ideas please ?
 
try to flash the phone
1_boatcore
2_eprome
3_fullflash
4_unlock the phone

it will be ok and i hope that i help u
B.R
ROBISH
 
no you only need to unlock it with original imei and phone 100% good tested so many times.......
 
U R TRUE MAN BUT HE MAY BE TESTED BY THEMSELF AS IT IS OLD SOLUTION AND IF HE UNLOCK MORE PHONES HE MUST KNOW THAT
 
Unlock it freia-10 again and the phone must be alive , I think your software (freia-15 is fake)!
Others way upload full flash to the phone and unlock again with "use original imei" section!
Regards
yaren
 
download from this site -http://www.siemensfreaks.com - mc60fubu /freia fls/ flashing the phone with freia, and after direct unlock no map is saved option activated. Your phone must be alived. Cheers and pray to ***.
 
Make what ROBISH says, but download good fufu from anyware. Your flash my be not good. Or try to update your phone with highest version of the software.
 
I get the same with my MC60 (Buz then nothing).
Downloaded files( boatcore,eprom,full flash and fubu) and tried flashing using Freia 15
(also frea 10) But whatever I try I get "COMM_SendBoot : boot file is not accepted".
Phone is version 7
The Siemens "Data exchang software" does not find the phone

Thanks in advance

Salute1

H
 
This meens there is no cutted test point in this phone. Try this: go to http://eh.student.utwente.nl/~landy/ user: mobile pass: elibom and download the highest version of swup. Connect the phone to computer with cable and start swup. Go to Serial config and configure the serial port and speed and click ok. Mark upper and down checkboxes "Skip" and click start. Then click for a second the On/Off button of your phone and wait the swup to update the SW version.
If after that the phone is still "buzzzzzzzzzz", then U need to cut the test point and flash your phone with freia.

Good Luck.
 
Thanks for your reaction tigertm.
Did as you mentioned with "WinSwup32 (NW Provider-Service Version) v1.43"
But I am getting "Cant connect to Mobile with BootstrapLoader on Com 1".


Any idea as to what can be done?
Regards,
Salute1
 
No, I don't know what is this, but be sure, that the com port to the Swup is this one to who is connected your cable, and try again. If yor cable is on com3, you never can update your phone on com1. Just try many times, then you make different changes to the options. If you using USB cable you need USB driver, to make your USB cable to com port. There is to landy.
Good Luck!
 
@tigertrn
No luck.. think I have damaged the phone when I mad the testpoint cut... will probably have to take it to a a prof. shop

Thanks again tigertrn
and best wishes
Salute1
 
When you are cutted the TP, you canot update the phone with swup. Download the good fubu, and use freia to flash the phone. It is the only one solution if you are not damage hardware your phone. Naw you my use only freia, or to try to repair TP, but it is difficult.

Good luck!
 
Hi,
Tried with Freia and half way cannot write the software, and I do not have the original fubu. Maybe I'm working with bad files.
Do you probably the files: (bootcore, eeprum and fubu, maybe a full flash!!) or do you have a link where I can download them?
Thanks a lot.

Salute1
 
Thanks for your help guys. Believe that I have damaged the phone beyond repair. It does not even respond to software when I press the "ON" key.

Best wishes
Salute1
 
try to flash the phone
1_boatcore
2_eprome
3_fullflash
4_unlock the phone

try to use the same version for all and the best feria like 9 or 10 if u can't try to contact me
B.R
ROBISH
 
Thanks for your kind offer robish_robish.

]I think that the soft version of my phone is v10
Please CYM.
Regards,
Salute1
 
Hi,
I am getting response from the phone now (at last) and followed as instructed, i.e.: bootcore, EEprom then fubu.
It accepted
a.bootcore (of C60 MC60 was not accepted);
b. EEprom accepted.
c. Fufu got error.
See logs from Freia 9:

"
Bootcore:

FREIA - Engine build 9, Frontend build 3
Thanks goes out for the following:
Maxim, Rolis, Sergey, PapaJoe, Lead,
TheWizard, Jozso (for hardware and cable
support and of course beta testing),
Nico, Victor, Pinker, Tom,
and all the others who supports ...
COMM_LoadBoots : selected phone family is 10
COMM_IsBootRunning : bootcode does not seem to be running
COMM_LoadBoots : Waiting to power on the phone ...
COMM_LoadBoots : phone is powered on
COMM_LoadBoots : internal loader version is 01.00
SEC_BCDIMEIToNormalIMEI : invalid decoded IMEI
COMM_LoadBoots : EEPROM IMEI (17) is corrupt
COMM_LoadBoots : original IMEI is 35199500304596 (locked)
COMM_LoadBoots : found SIEMENS MC60 lgX vff (1)
COMM_LoadBoots : flash ids are 00012212 [00000000] - FFFF
COMM_LoadBoots : phone ids are C880C7AE [00000000]
O.K.


EEprom:
FREIA - Engine build 9, Frontend build 3
Thanks goes out for the following:
Maxim, Rolis, Sergey, PapaJoe, Lead,
TheWizard, Jozso (for hardware and cable
support and of course beta testing),
Nico, Victor, Pinker, Tom,
and all the others who supports ...
COMM_LoadBoots : selected phone family is 10
COMM_IsBootRunning : bootcode does not seem to be running
COMM_LoadBoots : Waiting to power on the phone ...
COMM_LoadBoots : phone is powered on
COMM_LoadBoots : internal loader version is 01.00
SEC_BCDIMEIToNormalIMEI : invalid decoded IMEI
COMM_LoadBoots : EEPROM IMEI (17) is corrupt
COMM_LoadBoots : original IMEI is 35199500304596 (locked)
COMM_LoadBoots : found SIEMENS MC60 lgX vff (1)
COMM_LoadBoots : flash ids are 00012212 [00000000] - FFFF
COMM_LoadBoots : phone ids are C880C7AE [00000000]
O.K.


Full Flash (FUBU);

FREIA - Engine build 9, Frontend build 3
Thanks goes out for the following:
Maxim, Rolis, Sergey, PapaJoe, Lead,
TheWizard, Jozso (for hardware and cable
support and of course beta testing),
Nico, Victor, Pinker, Tom,
and all the others who supports ...
COMM_LoadBoots : selected phone family is 10
COMM_IsBootRunning : bootcode does not seem to be running
COMM_LoadBoots : Waiting to power on the phone ...
COMM_LoadBoots : phone is powered on
COMM_LoadBoots : internal loader version is 01.00
COMM_LoadBoots : EEPROM IMEI is 35195000254755
COMM_LoadBoots : original IMEI is 35199500304596 (locked)
COMM_LoadBoots : found SIEMENS MC60 lgX vff (1)
COMM_LoadBoots : flash ids are 00012212 [00000000] - FFFF
COMM_LoadBoots : phone ids are C880C7AE [00000000]
COMM_NormalWriteFlashBlock : erase response error at 00290000



Unlock:

FREIA - Engine build 9, Frontend build 3
Thanks goes out for the following:
Maxim, Rolis, Sergey, PapaJoe, Lead,
TheWizard, Jozso (for hardware and cable
support and of course beta testing),
Nico, Victor, Pinker, Tom,
and all the others who supports ...
COMM_LoadBoots : selected phone family is 10
COMM_IsBootRunning : bootcode does not seem to be running
COMM_LoadBoots : Waiting to power on the phone ...
COMM_LoadBoots : phone is powered on
COMM_LoadBoots : internal loader version is 01.00
COMM_LoadBoots : EEPROM IMEI is 35195000254755
COMM_LoadBoots : original IMEI is 35199500304596 (locked)
COMM_LoadBoots : found SIEMENS MC60 lgX vff (1)
COMM_LoadBoots : flash ids are 00012212 [00000000] - FFFF
COMM_LoadBoots : phone ids are C880C7AE [00000000]
COMM_UpdateIMEIBlocks : original IMEI is locked
O.K.

Second Trial Flash FUBU*:

FREIA - Engine build 9, Frontend build 3
Thanks goes out for the following:
Maxim, Rolis, Sergey, PapaJoe, Lead,
TheWizard, Jozso (for hardware and cable
support and of course beta testing),
Nico, Victor, Pinker, Tom,
and all the others who supports ...
COMM_LoadBoots : selected phone family is 10
COMM_IsBootRunning : bootcode does not seem to be running
COMM_LoadBoots : Waiting to power on the phone ...
COMM_LoadBoots : phone is powered on
COMM_LoadBoots : internal loader version is 01.00
COMM_LoadBoots : EEPROM IMEI is 35199500304596
COMM_LoadBoots : original IMEI is 35199500304596 (locked)
COMM_LoadBoots : found SIEMENS MC60 lgX vff (1)
COMM_LoadBoots : flash ids are 00012212 [00000000] - FFFF
COMM_LoadBoots : phone ids are C880C7AE [00000000]
COMM_NormalWriteFlashBlock : erase error at 00200000

And now when I wwant to try again I get: "COMM_SendBoot : boot file is not accepted" with every flash


Regards,
Salute1
 
hi guys , i got the same problem ,blue screen bzzzz then nothing ,
could you send flash files or link to download them , using feria
, when unlocking it says :

COMM_LoadBoots : selected phone family is 10
COMM_IsBootRunning : bootcode does not seem to be running
COMM_LoadBoots : Waiting to power on the phone ...
COMM_LoadBoots : phone is powered on
COMM_SendBoot : boot file is not accepted
 
Back
Top