C
cbdabomb101
Guest
so i just wanna make sure that my amp is ok to supply my subs
and im gettng two of these subs as well
heres are my amps specs
Technical Specification
RMS Power Range : 250-380 Watts
Number Of Channels: 2
Maximum Power: 760 Watts
Low Frequency response: 10 Hz
High Frequency Response: 50000 Hz
Built In Crossovers: Yes
Channel Separation: Yes
Features
CEA-2006 compliant
RMS Power @ 4 ohm: 125W x 2
RMS Power @ 2 ohm: 190W x 2
RMS Power @ 4 ohm bridged: 380W x 1
Selectable low-pass filter (80 Hz, 12 dB per octave)
Selectable bass boost (0, 6, 12 dB at 50 Hz)
Built-in Crossover has selectable LPF
MOSFET power supply
Speaker- and preamp-level inputs
Fuse rating: 30A x 2
Total Harmonic Distortion only 0.015%
2/1 Channel # Capability
Screw-Type Speaker Terminals
Dimensions: 14-1/8"W x 2-3/8"H x 11-13/16"D
and here are my sub specs
Technical Specification
Sensitivity: 91 dB
RMS Power Range : 150 Watts
Peak Power Handling: 800 Watts
Impedance: 4 Ohm
Low Frequency response: 20 Hz
High Frequency Response: 4500 Hz
Diameter: 12 Inch
Features
Nominal Power: 150W
Max Music Power: 800W
Nominal Impedance: 4 ohm
Sensitivity: 91dB/W
Frequency Response: 20-4500Hz
Magnet Weight: 25 oz.
Displacement: 0.060cu.ft / 1.69 liters
Cutout Hole: 11" Dia.
Mounting Depth: 5 3/4"
IMPP Composite Cone: reduce distortion, reproduces rich bass sound
Large Strontium Magnet: produces loud & tight bass
4-Layer, Long Voice Coil Design: high power and long excursion capability
Extended Pole Yoke
Extended Excursion Design
Large Binding Post
Best Tuned Parameters: CAD computer simulations were used to achieve powerful bass performance, superb sound quality and extreme reliability
Priced per speaker
so i should be fine right?
and my low output alternator should b fine as well with a capacitor?
and im gettng two of these subs as well
heres are my amps specs
Technical Specification
RMS Power Range : 250-380 Watts
Number Of Channels: 2
Maximum Power: 760 Watts
Low Frequency response: 10 Hz
High Frequency Response: 50000 Hz
Built In Crossovers: Yes
Channel Separation: Yes
Features
CEA-2006 compliant
RMS Power @ 4 ohm: 125W x 2
RMS Power @ 2 ohm: 190W x 2
RMS Power @ 4 ohm bridged: 380W x 1
Selectable low-pass filter (80 Hz, 12 dB per octave)
Selectable bass boost (0, 6, 12 dB at 50 Hz)
Built-in Crossover has selectable LPF
MOSFET power supply
Speaker- and preamp-level inputs
Fuse rating: 30A x 2
Total Harmonic Distortion only 0.015%
2/1 Channel # Capability
Screw-Type Speaker Terminals
Dimensions: 14-1/8"W x 2-3/8"H x 11-13/16"D
and here are my sub specs
Technical Specification
Sensitivity: 91 dB
RMS Power Range : 150 Watts
Peak Power Handling: 800 Watts
Impedance: 4 Ohm
Low Frequency response: 20 Hz
High Frequency Response: 4500 Hz
Diameter: 12 Inch
Features
Nominal Power: 150W
Max Music Power: 800W
Nominal Impedance: 4 ohm
Sensitivity: 91dB/W
Frequency Response: 20-4500Hz
Magnet Weight: 25 oz.
Displacement: 0.060cu.ft / 1.69 liters
Cutout Hole: 11" Dia.
Mounting Depth: 5 3/4"
IMPP Composite Cone: reduce distortion, reproduces rich bass sound
Large Strontium Magnet: produces loud & tight bass
4-Layer, Long Voice Coil Design: high power and long excursion capability
Extended Pole Yoke
Extended Excursion Design
Large Binding Post
Best Tuned Parameters: CAD computer simulations were used to achieve powerful bass performance, superb sound quality and extreme reliability
Priced per speaker
so i should be fine right?
and my low output alternator should b fine as well with a capacitor?