Food Processor Manual needed

On 10/8/2010 3:03 PM, Nancy2 wrote:


I'm sure I could operate it fine, but I'm looking to see if it can
handle stuff like pizza dough before I fry the motor.


--
Janet Wilder
Way-the-heck-south Texas
Spelling doesn't count. Cooking does.
 
On 10/8/2010 3:03 PM, Nancy2 wrote:


I'm sure I could operate it fine, but I'm looking to see if it can
handle stuff like pizza dough before I fry the motor.


--
Janet Wilder
Way-the-heck-south Texas
Spelling doesn't count. Cooking does.
 
In article , [email protected]
says...

ROF,L. If you had bothered with a google search you would have found
that (a) all approved devices do not have FCC IDs and that (b) electric
motors are classified by the FCC as "incidental radiators" and subject
only to the requirements that "Manufacturers of these devices shall
employ good engineering practices to minimize the risk of harmful
interference" (49CFR15.13) and that users of the device can be required
to quit using it if that use is causing harmful interference (49CFR15.5)

Further, FCC does not in general review designs, they require that
samples of the completed device be tested.

As an exercise, please since you are so certain that everything with a
motor has an FCC ID, go down to Home Depot and write down the FCC IDs
for all the power tools on display.
 
In article , [email protected]
says...

ROF,L. If you had bothered with a google search you would have found
that (a) all approved devices do not have FCC IDs and that (b) electric
motors are classified by the FCC as "incidental radiators" and subject
only to the requirements that "Manufacturers of these devices shall
employ good engineering practices to minimize the risk of harmful
interference" (49CFR15.13) and that users of the device can be required
to quit using it if that use is causing harmful interference (49CFR15.5)

Further, FCC does not in general review designs, they require that
samples of the completed device be tested.

As an exercise, please since you are so certain that everything with a
motor has an FCC ID, go down to Home Depot and write down the FCC IDs
for all the power tools on display.
 
On Sat, 9 Oct 2010 10:01:10 -0400, "J. Clarke"
wrote:


It would never occur to me to look for an FCC stamp. I don't look for
one specifically, but am always assured when I see an Underwriter's
Laboratory stamp on items.

--

Never trust a dog to watch your food.
 
On Sat, 9 Oct 2010 10:01:10 -0400, "J. Clarke"
wrote:


It would never occur to me to look for an FCC stamp. I don't look for
one specifically, but am always assured when I see an Underwriter's
Laboratory stamp on items.

--

Never trust a dog to watch your food.
 
On Sat, 9 Oct 2010 10:01:10 -0400, "J. Clarke"
wrote:


Power tools eh...
are you implying that I should have an FCC ID for my penis? ;)
My atomic clocks all have FCC IDs, my remote weather station too...
but not my meat grinder. hehe
 
Janet Wilder wrote:

-snip-

Did you call the company? It isn't something we think to do these
days-- and often is a waste of time but sometimes you get lucky.

I called Whirlpool in 2007 for a manual that I wasn't able to find
online. [10yr old washer] A real person answered, directed me to
customer service, who said 'No problem', apologized for their website
and emailed me a copy. Done in 2 minutes.

Jim
 
On Sat, 9 Oct 2010 10:01:10 -0400, "J. Clarke"
wrote:


Power tools eh...
are you implying that I should have an FCC ID for my penis? ;)
My atomic clocks all have FCC IDs, my remote weather station too...
but not my meat grinder. hehe
 
Back
Top