Dead M65

  • Thread starter Thread starter zahyr
  • Start date Start date
Z

zahyr

Guest
I have dead M65. I dont know how it was "killed", I was trying to repair it with solution for phones damaged with eepromtool, but not succeded. I was trying to use PapuaUtils and "replace 76, 5008, 5009, 5077" , "Replace Master", Recalculate Keys in flash" and it says:

Checking values SKey from page "CODES" ...
Using Skey: 5752****
AutoIgnition...
Transmit Boot...
Boot loaded ...
Retrieve information...
FlashID: 0001,227E
SIEMENS M65 3536670058*****
Wrong information !
HASH: 733EA4DB10E93DB48A5*********
Unregistered version !
Use ESN from page "CODES" !
OTP ESN: F68181F7
OTP IMEI: 3536670058*****
All EEP blocks: 233
Block 52,76,5008,5009,5077,5121,5122,5123 found .
Error code asknowledge command erase segment A02207A3!
No ask. tocommand writting segment A02207A3!
Impossible replace block 5008!
Replace not good- check phone !


I tried to write to phone rapair flash, but vklay do error in about 21% of flashing.
How to repair it? Please help
 
I cant write firmware, because there is error in flashing at 21%.

I cant unlock phone by papuautils by SKEY too:

Enter key....
SKey enter !
Wrong key !

What a ***** phone :/ any solutions to repair it?
 
abou flashing error: check baterry, try lower speed, check cable , other case - change flash bga. btw: what flasher u use?
 
Battery is full, cable is good too (flashing other phones 100% ok) i use SST 5.32 and Vklay.

I have entered SKEY now (deleted old eeprom and flashed new backup from other m65) and i have factory mode, but when i try to recalculate keys in flash, i have that:

Error code asknowledge command erase segment A0FE0010!
No ask. tocommand writting segment A0FE0010!
Impossible replace block 52!
Replace not good- check phone !

When i want to do "freeze" i have:

Checking value entry and needed block ...
IMEI: 353667005******
Cod(05): OTP blocked !
Cod(0D): Keys writted in BCORE!
In this mode FREEZE impossible !

(mode is set to factory)
how to repair it? :/
 
Anybody know how to flash that phone? I was trying by vklay and sst and error at 21%.
 
Check your batterie or try to use external power supply (3,9V)

I think your battery is empty
 
So any solutions for replace block 0052? Maybe someone will say to me for what i have to replace 0052?
 
Your flash IC unsoldered or damaged, use some good flux and rehot it carefully but better you reball or change it with now one.
 
I cant write blocks: 0x006E0000-0x006F0000. Other blocks i can write with no problem. I have rehoted flash with flux and there is that same. I can't reball bcause i dont have sieves for that BGA :/
 
Ok, now i have repaired EEPROM, but there are another problems:

1. Freeze failed?
OTP IMEI: 35366700xxxxxxx
OTP ESN: F68xxxxx
 
I'm lookin for a full flash and eeprom file to flash my Siemens m65. It has software damage, that's why i dont want to use Winswup. I read here at this post, that some of you guys have it. Please, post the link where I can download it.
The version of the software that is in the phone is ver. 41.
I read many post and they little confuse me. Do I need also the bootcore file or not, when I flash the phone with flash and eeprom? Do I need to do a TP, not cut, just GND?

Thanks in advance for any help.
 
Back
Top