c55 v18 dead after A50_C55 unlocker.rar

  • Thread starter Thread starter sloper
  • Start date Start date
S

sloper

Guest
I try today to unlock C55 v18, lg6 (phone have blue led on display)

I use A50_C55 unlocker.rar

Before unlock I make buckup of eeprom !!!! good work

After unlock, phone say bzzzz, 2 sec !

I try write original eeprom with "Siemens A50 & C55 Wizard. Version 4.00", but after 33% I get message

Verification failed: Buffer (D6DA20D6) and flash (6824AF5F)

Cancel - Retry - Ignore

Is it possible to reanimate this phone, because I have original eeprom file !

regards Boba
 
Hiya

I had same prob...

Solder test point resistor back, flash phone with winswup, then put back original eeprom and u have it alive again...

And don't use same unlocker on that type of phone

Simlock zoneis not in eeprom, it is in flash...



BR

Vule
 
It' s really strange flash IC that cannot be recognized by winswup!!!
Now we know the flash ID =002c0017. Can you tell me what is written at the flash IC to check if it is correct.
If winswup can't write this type of flash then all the software can't write this flash type till now.Then try to find the newest winswup or wait for new bootloaders
 
@comunicatel

If is this help you, I can flash this type IC FW206 with winswup,
but when try flashing without resistor with Unisiemens, selection C30, with loaders for C55 , after that, winswup, get me only FFFFF
 
@vule

WHat about that prog? Some people says that work fine
for version V21 for C55, and for A50 V10?

True or not?
 
try fullflash with wizzard.
then write imei( with wizzard or other tool that can recalculate simlock zones).
if flash ID FFFF and winswup can't flash it's not a sowtware problem
 
Curently F640 flashes with these flash IDs are not supported by any software: micron 2c0017 and intel 890017.
For now it is known only for C55 with this types of flash.
So if you have one these phones do not try to unlock.
Solution will be soon
 
I tried several things, it seems that I cannot read eep with any soft....Everything blank in hexedit...
I guess the only solution for me is map now......
 
@Vule

Do You know maybe can it be unlocked by writing unlocked FW
If not- how?

Greetings to neighbours........
 
Before unlocking:

Read eeprom
Open in hexedit
You'll see if eep is read correctly or not...
So, if You can read it, You can write it, and also unlock it.
 
Hiya

Guess what guys....

Phone i had killed and revived few days ago, returned to me today...Dead cow


I have original eeprom backup but i can't write it back...Stops at 33, 66 and 100%....

Damn, i love this job...


BR

Vule
 
I try with wizard 4.0 flashing full flash but Verification Failed show me per 2% permanently!
By eeprom writing I get on 33%, 66%,99% "Verification Failed"

After that when I read eeprom with wizzard, eeprom is EMPTY !

Board is made before 20 days !?!?!?!
I find date on board 24.04.2003
 
@shoneb
No map will not help you.
I think that the problem is in the boot ,but why winswup can't flash this micron IC is still an enigma for me.
shoneb , do this open you phone and tell me what is written at the flash IC . I need the type and the product number of the flash IC. I'll try to fix boots and when I finish my software I'll send you a free test tool
 
Hello


I guess i was extremely lucky with reviving my phone.... Version was 18 and cover gray with metal part around display, blue leds...


I am sure that is new flash type in it but i did not have chance to take a second look, 'cause customer was in hurry...

Anyway, i have readed eeprom from it and if anyone needs it i will send it or upload it ...


BR


Vule
 
Back
Top