All about EL71 here and only here !

  • Thread starter Thread starter Abe
  • Start date Start date
here is it from working phone with intel chip, and tested many time

EL71_V31_LG1__intel_.rar
 
Hello dagos,

my cable should be no problem, I have used it to flash 1 A31, and I assume the CPU also have no problem, so probably as the issue of bootcore, and from Gehstock's replay, he give a solution as below:
---------------

Use the Attached File (EL71 v9) open with hexeditor and enter ur Hash and IMEI
Save the New bcore and Flash with Vklay

Set VDown is in Adress 0x03E020
---------------

Then how to get the hash? I could get the IMEI from the lable.

Thanks!

Ben
 
The A31 serial cable only uses 3 (Tx), 4 (Rx), 5 (GND) and 7 (+5V) pins. Then, I can not convert it to USB datacable.

I didn't know that EL71 unlocks using USB datacable...
 
I have a back up from bootcore. It was damaged when I ticked "neuer bcore v22 (R65), v11(x65)" before do job. Exactly the same mistake as TheCult did.

Here is the log :

Rote Taste dr
 
EL71(ELF1 Orange 25Lg41)

With BsReader i read :
Hash 47A77CD91CF1C295B495EEA45D9971FF
ESN 6F689970
IMEI 358941002558891

Xflasher and Papua can't calculate Skey and Bkey.
Any solution to find these Keys?
Perhaps new algo.

samrydz
 
i use this cable but no connection with SiMoCo and no connection with Siemens Data echange soft.

only connect with papa

whats problem...
 
THANKS A LOT BROS AND PROS. THE F****N set repaired after all!!!!!!!!!! what an upcome.......Dream Box failed, SST failed, didnt try with martech but I think it will fail too. So dont bother try with them, Just follow this thread set will be okeyyyyyyyyyy
*
 
Hi All,

I tried with paupa V1.11b(with TP), flash---do the job, the information as below:

Auto Ignition...
Transfer boot...
BOOT is loaded...
Pause 2 sec...
Getting Information...
FlashID: 0000,0000 (64Mb)
Data are read through incorrectly!
r
 
http:///vbb/showpost.php?p=2109800&postcount=4

v 0.9.3b (all not working fonction are enabled in this version)
 
im working on this phone for a week.
thanks bourri for help.i'll try some other ways and back to you
)
 
And i have never used v_klay,papua or x65 flasher before..

what does it mean?

it means im not stupid
 
need help on my benq-siemens el71, phone is disabled and asking for a phone code.
IMEI: 358941001692733
 
hello


Boot in "Service mode" Ok
Awaiting Power On phone...
Getting Information:
Model: SIEMENS EL71 41 lg91
Phone is in "Service Mode" mode
IMEI: 35*************
SecurityStatus: CustomerMode
HWID: 407
Attention: Not matching HWID and Phone model!
Accumulator Voltage: 4253 mV.
Getting Information:
Model: SIEMENS EL71 41 lg91
Phone is in "Service Mode" mode
IMEI: 35*************
SecurityStatus: CustomerMode
HWID: 407
Attention: Not matching HWID and Phone model!
Accumulator Voltage: 4229 mV.
EELITE Info:
Free buffer 166432 bytes, free at all 206240 bytes, free for deleted 206240 bytes.
EEFULL Info:
Free buffer 14784 bytes, free at all 466272 bytes, free for deleted 204192 bytes.
MAP info:
Date: 27/09/06, Variant: A 703,
Std-Map/SW: 1/39, D-Map/Prov.: 193/77
To Get Extended Info - Enter Skey into the phone!
Phone operated: 9536631 sec.
Total Talk time: 11420 sec.
FlashID(1) - Manufact. code: 0089 (Intel), type: 887E.
DisplayID(1,64): Unknown.


x65flasher work for flash my el71?


my phone not turn on i have just a beep.
 
...unrar archive from attachemment and copy in the phone (Java/Application) using phone manager.
For unlocking steps (with Java midlet) search on this forum (have manny posts regarding this...).
dagos
 
i don't know about name

i make my cable by myself

it's simple RJ45 cable with 3 wires (RX, TX & GND) & work with universal box


use search that's so easy, this thread is not about cable pinout, it's about software problm of EL71


thx
 
Back
Top