L
loren
Guest
And the bootcore is always damaged but I still can' t write the backup I have.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
G
GSM RAJ
Guest
here is log
Auto Ignition...
Transfer boot...
Boot in "Service mode" Ok
Awaiting Power On phone...
Getting Information:
Model: SIEMENS EL71 22 lg1
Phone is in "Service Mode". SecurityStatus: "CustomerMode"
IMEI: 358941003561795
HWID: 407
Accumulator Voltage: 4159 mV.
Boot in "Service mode"...
Press RED key (Power ON)!
Auto Ignition...
No answer to boot load!
Check port number, cable, phone, mode!
Boot in "Service mode"...
Press RED key (Power ON)!
Auto Ignition...
Transfer boot...
Boot in "Service mode" Ok
Awaiting Power On phone...
Getting Information:
Model: SIEMENS EL71 22 lg1
Phone is in "Service Mode". SecurityStatus: "CustomerMode"
IMEI: 358941003561795
HWID: 407
Accumulator Voltage: 4159 mV.
Getting Information:
Model: SIEMENS EL71 22 lg1
Phone is in "Service Mode". SecurityStatus: "CustomerMode"
IMEI: 358941003561795
HWID: 407
Accumulator Voltage: 4141 mV.
Code(05): OTP is Closed for write
Code(0B): BootKEY is unknown. Block 320 is absent.
Code(0D): Keys is stored in BCORE
Code(10): BFC functions are inaccessible
Code(15): Full mode (not SC)
Code(19): The control is On
Code(1D): 512x blocks presents
EELITE Info: free buffer 186336 bytes, free at all 206304 bytes, free for deleted 206304 bytes.
EEFULL Info: free buffer 104160 bytes, free at all 466432 bytes, free for deleted 204352 bytes.
MAP info: Date: 30/08/06, Variant: A 151, Std-Map/SW: 1/22, D-Map/Prov.: 159/103
To Get Extended Info - Enter Skey into the phone!
Phone operated: 32813329 sec.. Total Talk time: 25954 sec.
FlashID(1) - Manufact. code:0020 (ST), type: 8819. DisplayID(1,65): Sharp Sharp LHH9168.
i am using uni box and a31 cable.
thx for help.
Auto Ignition...
Transfer boot...
Boot in "Service mode" Ok
Awaiting Power On phone...
Getting Information:
Model: SIEMENS EL71 22 lg1
Phone is in "Service Mode". SecurityStatus: "CustomerMode"
IMEI: 358941003561795
HWID: 407
Accumulator Voltage: 4159 mV.
Boot in "Service mode"...
Press RED key (Power ON)!
Auto Ignition...
No answer to boot load!
Check port number, cable, phone, mode!
Boot in "Service mode"...
Press RED key (Power ON)!
Auto Ignition...
Transfer boot...
Boot in "Service mode" Ok
Awaiting Power On phone...
Getting Information:
Model: SIEMENS EL71 22 lg1
Phone is in "Service Mode". SecurityStatus: "CustomerMode"
IMEI: 358941003561795
HWID: 407
Accumulator Voltage: 4159 mV.
Getting Information:
Model: SIEMENS EL71 22 lg1
Phone is in "Service Mode". SecurityStatus: "CustomerMode"
IMEI: 358941003561795
HWID: 407
Accumulator Voltage: 4141 mV.
Code(05): OTP is Closed for write
Code(0B): BootKEY is unknown. Block 320 is absent.
Code(0D): Keys is stored in BCORE
Code(10): BFC functions are inaccessible
Code(15): Full mode (not SC)
Code(19): The control is On
Code(1D): 512x blocks presents
EELITE Info: free buffer 186336 bytes, free at all 206304 bytes, free for deleted 206304 bytes.
EEFULL Info: free buffer 104160 bytes, free at all 466432 bytes, free for deleted 204352 bytes.
MAP info: Date: 30/08/06, Variant: A 151, Std-Map/SW: 1/22, D-Map/Prov.: 159/103
To Get Extended Info - Enter Skey into the phone!
Phone operated: 32813329 sec.. Total Talk time: 25954 sec.
FlashID(1) - Manufact. code:0020 (ST), type: 8819. DisplayID(1,65): Sharp Sharp LHH9168.
i am using uni box and a31 cable.
thx for help.
N
njben
Guest
Hello All,
Now one ask me to fix the problem with the El71, the status is : totally dead, no light.
when I use paupa flash--dojob.
the information is: auto Ignition...
boot not loaded,
boot released.
what happened? how to fix this issue?
Now one ask me to fix the problem with the El71, the status is : totally dead, no light.
when I use paupa flash--dojob.
the information is: auto Ignition...
boot not loaded,
boot released.
what happened? how to fix this issue?
B
BouRRi_GSM
Guest
connect phone to papua using TP, check only pause 2s
and post log
(for repairing eeprom block u must send skey to phone, phone must be in factory mode, i skey not sended to phone , u can't acces to some block in eeprom)
post log, i will try to help u
and post log
(for repairing eeprom block u must send skey to phone, phone must be in factory mode, i skey not sended to phone , u can't acces to some block in eeprom)
post log, i will try to help u
S
shakeelajmal
Guest
What about my problem man? what should i do? is swup flash file help me or not?
s68 is not useable without bluetooth
BR
s68 is not useable without bluetooth
BR
F
florinmar
Guest
i need prototype fubu for el71
B
BouRRi_GSM
Guest
maybe it's software problem like all Siemens dead by Himself
i repair some EL71 dead by himself
at the first, connect phone with TP and Papua, and post here log file
----------------------
if bcore is ok try do this:
try use x65flasher-2103,
connect phone with TP, read Full Flash backup, backup eeprom, backup bcore
Flash phone with Full Flash (u must know Flash Chip ID before)
restore eeprom (don't need restore bcore bacause x65flasher-2103 skip bcore writing)
disconnect phone and try power on the phone
if eeprom is ok phone must be ok after this process
---------------
another idea,
try format FFS before, many problem are caused by user data
good luck
i repair some EL71 dead by himself
at the first, connect phone with TP and Papua, and post here log file
----------------------
if bcore is ok try do this:
try use x65flasher-2103,
connect phone with TP, read Full Flash backup, backup eeprom, backup bcore
Flash phone with Full Flash (u must know Flash Chip ID before)
restore eeprom (don't need restore bcore bacause x65flasher-2103 skip bcore writing)
disconnect phone and try power on the phone
if eeprom is ok phone must be ok after this process
---------------
another idea,
try format FFS before, many problem are caused by user data
good luck
T
turktwister
Guest
what is going on ?
R
ra1ex
Guest
If to use Recaclulate Keys in Flash or Replace 76...blocks with Papua ver1.0.x, then it is possible to swup in any firmware. 41sw it is better to NOT use.
A
Afzaal
Guest
So how can v kno Chip info b4 perform Unlocking Steps.
N E idea?
BR.
N E idea?
BR.
R
rvs
Guest
I refer that the cable is a standard Serial cable RS232 with connector Siemens A31, and it does not use 9V battery.
G
Gehstock
Guest
I Search a User with SST Dongle .
SST will support ST-Flash (0020 (ST), type: 8819) i will insert the BootLoader in PapuaUtils for a Free Solution. But i Need a Comlog (with the BootLoader) Write me a PM
SST will support ST-Flash (0020 (ST), type: 8819) i will insert the BootLoader in PapuaUtils for a Free Solution. But i Need a Comlog (with the BootLoader) Write me a PM
B
BouRRi_GSM
Guest
this log when phone is in "Service Mode"
u must perform TP, and press "Do job" in Flash tab of papua
use search in forum
br
u must perform TP, and press "Do job" in Flash tab of papua
use search in forum
br
B
BouRRi_GSM
Guest
u can Flash phone and repair bcore for free,
but if u haven't eeprom backup, u must use pro tool to do repair eeprom after repair
connect phone with TP and papua, Do Job and post here the log file
but if u haven't eeprom backup, u must use pro tool to do repair eeprom after repair
connect phone with TP and papua, Do Job and post here the log file
G
Gehstock
Guest
Use Midlet Method this Flashtype is not Full supported
A
Afzaal
Guest
Any link for
last ver. of popua utilis
Preffered translated One.
BR.
p.s don't redirect me chris02 thread that link is no more working.
last ver. of popua utilis
Preffered translated One.
BR.
p.s don't redirect me chris02 thread that link is no more working.
A
Aymen G
Guest
100% working :
Auto Ignition...
Transfer boot...
BOOT is loaded...
Pause 2 sec...
Getting Information...
FlashID: 0089,887E (64Mb)
CFI: 1 : 256*262144,
ELF1 SIEMENS 35XXXXXXXXXXXXX
HASH: B368C600EFE4DDAA938E52C3CA55D98F
OTP ESN: 8D8D1196
OTP IMEI: 35XXXXXXXXXXXXX
At occurrence of mistakes reduce speed of port!
Bcore x85 series found.
Search of a segment EELITE...
Search of a segments EEFULL...
Find blocks: 52,76,5008,5009,5077,5121,5122,5123
In total EEP blocks: 141
EEPROM Blocks saved in .\Backup\8D8D1196_EEP_070503154216.eep
Replacement of blocks EEPROM in the buffer ...
EEPROM: Block 76 does not require replacement.
EEPROM: Block 5009 does not require replacement.
EEPROM: Block 5008 replaced.
EEPROM: Block 5077 replaced.
EEPROM: Block 5121 replaced.
New Master codes:
*#0000*12345678#
*#0001*12345678#
*#0002*12345678#
*#0003*12345678#
*#0004*12345678#
*#0005*12345678#
Record of the changed blocks in phone...
Write down EEPROM segments...
EEPROM segments write down.
Boot released. Everything is closed.!
Auto Ignition...
Transfer boot...
BOOT is loaded...
Pause 2 sec...
Getting Information...
FlashID: 0089,887E (64Mb)
CFI: 1 : 256*262144,
ELF1 SIEMENS 35XXXXXXXXXXXXX
HASH: B368C600EFE4DDAA938E52C3CA55D98F
OTP ESN: 8D8D1196
OTP IMEI: 35XXXXXXXXXXXXX
At occurrence of mistakes reduce speed of port!
Bcore x85 series found.
Search of a segment EELITE...
Search of a segments EEFULL...
Find blocks: 52,76,5008,5009,5077,5121,5122,5123
In total EEP blocks: 141
EEPROM Blocks saved in .\Backup\8D8D1196_EEP_070503154216.eep
Replacement of blocks EEPROM in the buffer ...
EEPROM: Block 76 does not require replacement.
EEPROM: Block 5009 does not require replacement.
EEPROM: Block 5008 replaced.
EEPROM: Block 5077 replaced.
EEPROM: Block 5121 replaced.
New Master codes:
*#0000*12345678#
*#0001*12345678#
*#0002*12345678#
*#0003*12345678#
*#0004*12345678#
*#0005*12345678#
Record of the changed blocks in phone...
Write down EEPROM segments...
EEPROM segments write down.
Boot released. Everything is closed.!
F
foosoomin
Guest
So the answer is ????
DCA-140 or DSC-100 ?
DCA-140 or DSC-100 ?
S
snsoftkiller
Guest
can you btw upload again the fullflash.
BR
BR
D
dagos
Guest
...in yor case you have thre possibility:
1. change your cable
2. rehot CPU
3. your bootcore is damaged. Repair it.
Br,
dagos
1. change your cable
2. rehot CPU
3. your bootcore is damaged. Repair it.
Br,
dagos