All about EL71 here and only here !

  • Thread starter Thread starter Abe
  • Start date Start date
I made TP now, but with Vklay 3.3, X85 (Testpoint + pause 1.3) loader it says:
"An unknown error occured while accessing COM1 - Loader: WriteMemory: Unknown answer after erase flash readed: 0x4545, but must be 0x0202."

I think it's because the loader is not good, I only can read memory, but i can not write. the same problem with x65flasher.

Can someone send a el71 (testpoint) loader for vklay, which is working?
regards
 
Hi,


I will close all threads about EL71, and make this one STICKY,

Please post about your problems and ideas only here, in this thread ..




Regards
 
Good share....but it would be nice if u or any one else Upload this File on a Good Server as on Rapidshare wont allow me to download
 
Hi guys

I need help

My EL71 has firmware 31 and I wish to update to 45.

I have a DCA-100 cable and papuaUtils gives me this info:

Phone is in "Normal Mode". SecurityStatus: "FactoryMode"
IMEI: 358941004422799
HWID: 407
Accumulator Voltage: 4025 mV.
Code(05): OTP is Closed for write
Code(09): BootKEY is stored in EEPROM
Code(0D): Keys is stored in BCORE
Code(13): Full access to BFC functions
Code(15): Full mode (not SC)
Code(19): The control is On
Code(1D): 512x blocks presents
EELITE Info: free buffer 185696 bytes, free at all 206240 bytes, free for deleted 206240 bytes.
EEFULL Info: free buffer 201408 bytes, free at all 466432 bytes, free for deleted 204352 bytes.
MAP info: Date: ??/??/??, Variant: A 510, Std-Map/SW: 1/31, D-Map/Prov.: 255/255
Factory (OTP) IMEI: 358941004422799 - matches to flash data.
ESN: 12C79DE8
HASH: 0796924566EDD314B8C4410765363BA3
BKEY in block 320 = B76EFF919CB1976FA712F4834F906904
SKEY in 5122 = "X" 34308553
Minimum number of firmware: 31.
Bcore ID: 0300, version: main_1.0_V9".
Phone operated: 2006619 sec.. Total Talk time: 9528 sec.
FlashID(1) - Manufact. code:0020 (ST), type: 8819. DisplayID(1,65): Sharp Sharp LHH9168.

But I can not switch to service mode or use x65flasher-2103 as nothing happens when i switch off the phone and press the red key.

Using a firmware update gives error "access to phone denied"

Any ideas on how I can update?

Cheers
 
thx BB-gsm to make one of EL71 thread sticky

plz for all we have info or idea post here

also post Full Flash and bcore from working phone


thx
 
I have an el71 with damaged bcore
I have a backup of bcore too but vklay give error message :
"no answer from boot boot.bin"

Plse, could you provide some hlp ?
 
i agree tested by me i used it with martech box and test point adapter connect to the GND select manual mode.... press the black connector botton and all will be ok.
 
i did gehsocks way.read hash,open hex and make my own file.but i cannot write boot with v-klay

Can you help gehstock,bourri and others..

br
ttwstr
 
A quick question to ask,

1) After we have switched off the phone, the flash will light up when you pressed the Off/End button. This happens on ELC1, FW 39 & 41

2) The production date is 9/Sep/06 (U9)

3) When we're using Winswp to upgrade FW, while the 1st Skip is checked, the flash light will lit up when you press the Off/End button for upgrading progress, till it complete


Anyone faces this problem too ?
 
Read through once again. Upload works with 38 fw ONLY! If firmware in the phone is not 38 then phone is dead! But anything terrible . Use WinSwup and swup 38 firmware into the phone.

p.s. Now PapuaUtils V1.0.4 present and method with patch firmware has become outdated. With version 1.0.4 use Recalculate Keys in Flash. Or Replace 76,5008,5009,5077 if only unclock it is necessary.
 
Mr. ra1ex thanks very much .Phone is ok .
And thanks so much to Mr. gehstock and Mr. BouRRi_GSM for your help . All is ok , my phone is now working .
 
...me too. Is my pleasure to help you.
Best regards from the "Papura Voda" country (Romania)
dagos
 
Back
Top