A55 wrong software

  • Thread starter Thread starter darkeye_bob
  • Start date Start date
D

darkeye_bob

Guest
Not quite. Only for a few days, hours. The customers come back with WS phones ! If you replace the flash with anotherone, the phone live happy ever after !

I hope that Benq will do a better job with Siemens mobiles !
 
Hi to all of you fine people! I'd like 2 know what should I do in this case. it's about A55 giving me headache.I've cut test point with drill, about 0,3 mm. With or without testpoint, software like Freia, Winswup and so on don't sense the phone at all. I've connected 2,3,4 just like in Bruce's pinouts foe Siemens C55. Phone still dead, sometimes says: wrong software, otertimes vibrating goes on and stuff like that. Help! Also a lg. pack with Romanian needed. Thanx in advance
 
check if it does need to cut testpoint. then use direct unlock no map is save. rewrite imei then check update flash imei then press ok. short click power button... have tried it already!
 
FIRST OF ALL you cut to deep the testpoint , you may need a testpoint repair sollution.
Question: what was the situation with your phone before you opened it?
Was it working ok-just locked on a network and you tried to unlock it, or it was dead and you tried to flash it to revive?If it was working and you cut testpoint and then it did not worked you REALY bad cut the testpoint, if not there are two situations r you bad cut the testpoint, or you have bad contacts at the power IC(DIALOG) or at the CPU or/and the FLASH.
In my oppinion i would try first to reheat the CPU+FLASH+DIALOG, and after that i would try to flash the phone.FOR THE FUTURE: DO NOT CUT THE TESTPOINT MORE THAN 0,1-0,2 mm(MAXIMUM).
Anyway good luck!
regards,
doktortelecom
P.S. If you still have any questions you may contact me by Yahoo messenger(id:doktortelecom) or here on this forum.
 
usually with this kind of problem, you need to direct unlock without save map. rewrite imei then check update flash imei then press ok. but if the problem comes back, rewrite its eeprom using .fls flash file. usually after flashing when pressing power on, it would blink. just use the smae procedure as what i have mentioned above.. hope i have solved your problem.. B.R.
 
Give me your e-mail and i'll give you full flash -romanian lang. included.
regards,
doktortelecom
 
Hi bro..
Try to just only unlocked with SST after Repair button i think its work bcz iam also make like this many pes..

Thanks
FromLockUnlock Team
 
just make map from phone then make a log from map and then write log to the phone ur phone will be O.K
 
the best solition for A55 Showen Wrong Softeware
just flash it with good version and if you need test point do it
i try it and its work 100 %
good luck
 
I have the same problem... WS... with 3 A57, but they have no testpoint cut.
I'm pretty sure that the customers don't try to unlock the phones... any ideea for repair, or similar experience with this problem ?

Tnx in advance !
 
Plz Help My A55 Showen Wrong Softeware But When I Tried To Creat Log Or Map With Freia The Program Write Phone Not Powered Up But The Phone Is Powered.
My Best Regards,
 
select "Bootcore Bug" in settings,
then "unlocking" functions, select
"direct unlocking no map is saved",
press button "use orginal IMEI"

then power on the phone

well done
it works if your phone is locked or not.
 
hi mates i have a55 wrong software soluyion.do thes steps one by one
1st;rehaot flash & cpu with flux normally
2nd:cut test point deaply
3rd:repair software with sst
tested by me on 2 sets.100% working
BR
SHAMI
 
if hard: rehot cpu and flash
if getting "wrong software" after bad unlock: use repair sst or reunlock it using original imei...
 
Back
Top