Z130 All night was charging .. now dead

  • Thread starter Thread starter BB-gsm
  • Start date Start date
B

BB-gsm

Guest
Hi all,

My friends Z130 was left with connected charger all night long, and in the morning he found it not turning on ...

One thing, when I connect charger in phone, charger connector led gets RED !

I cant flash it with MultiDownloader and USB cable, as it cant enter flash mode with pressing 4 + power on (are these correct buttons?) ...

I cant use LG7050 COM cable with this multidownloader as it works via USB I guess !


Maybe its hardware problem, or maybe battery is dead (voltage is up to 4 though!), I have no other battery here yet


Any ideas ?
 
u can try what Pandemonio100 said before

for Download mode hold 9 and press power on

the Z130 MultiLoader v5.2 work with USB (same Z140-LG3G usb cable)

unlock work with COM cable (LG7050)
 
Nothing happens after pressing 4+9+power on

PC is not detecting anyhing with Z130 usb cable connected with phone !

I dont understand where to connect external supply (5v ?) ..

And I dont want to fck up the phone wholly,
I am not good in hardware but if you could tell me what to check/remove/short I`ll ask my hardwarer to do when I`m at work


Regards,
B
 
R.E Z130 All night was charging .. now dead : ur best bet is obtain a new charger and battry, if this doesn't work then ur fone's capacitors r ****ed if da fone woz chargd switchd on on standby mode like with a couple of my motorola e1000s they r as ****ed as anything coz they were left on standby mode whist charging, if u do get ur fone fixd, switchoff the fone b4 stickin it on charge m8
 
@BB-gsm

this sometime happens, when you put the phone on charging while you go to sleep, and in next morning you wake-up but phone does not . ie it dies.

so now lets come to the point

1. as already said first try with other good charger and battery.
2. if other charger is not available, simply check if the old charger is giving output voltage or not. if there is about 4 to 6 volts DC, you can assume it as good, no need to change it.
3. attach the charger with the phone , donot put battery in the phone, quickly check if there is any voltage at the battery connectoer fo the phone,
there should be some voltage , it varies from set to set, you can get min 1.8 or maximum about 4 to 5 volts.
4. if you get these voltages, you can assume that at least charging + some part of power ic is working.
5. if you dont get any voltage at the battery terminals it means charging section is not working.
6. if you dont get charging voltage at the battery terminals , normally , its due to fuse is ****n up., it can be bypassed with very thin wire.
7. if you find fuse is OK and still no volatge at battery terminals , it means there is some short circuit in the charging section.
8. this can also be identified very easily, to do so pls open your set , attach charger to it , wait for few mins, than quickly check by touching various parts , near to the charging connector and tha rest of the board, you will find few small parts heating up . Normally these parts are either capacitors or protection diode , which are grounded by one end, you need to identifies these over heating parts, once you find it, simply remove it , no need to put new in replacement.
by doing so now you must get DC voltage at battery terminal of the phone.
 
next part after you or some one find this info by me usefull.

thanks
br
AshwaniGaur
 
if u have external power supply with current and voltage indicator,

use 4.2V from external power supply
remove batterie, and put + of external power supply to + Vbatt and - of power supply to - Vbatt

if in current indicator u see more than 0 mA, therefore ur phone have a shorted circuit (damaged circuit)

if not try
 
BouRRi_GSM said:
if u have external power supply with current and voltage indicator,

use 4.2V from external power supply
remove batterie, and put + of external power supply to + Vbatt and - of power supply to - Vbatt

if in current indicator u see more than 0 mA, therefore ur phone have a shorted circuit (damaged circuit)
************************************************


To make it more clear if you get excevie current drain @more than 150ma in power off position than there is short circuit .

before doing any such thing pls set current limit to 150 mA in your regulated power supply unit. other wise it can do more damage.


br
AshwaniGaur
Click to expand...
 
Let us try to understand with more clear vision:

pic no 1 is flow chart for CHARGING PROBLEM.

Pic no2 is Circuit for Charging Section.
If Charger is tested OK and still you get no voltage at battery terminals of the phone , pls try removeing parts with RED marking.

ENJOY

br
AshwaniGaur
 
IF set does not power on or consumes more current@>=100mA AND flashing also not possible pls check as in the pic:

ENJOY

br
AshwaniGaur
 
IF set still demands more current pls remove first COIL F803 and check again if current becomes normal than either C824 OR C827 OR BT-Module is FAULTY.
This can further tested by fixing again F803 and remove C823+827, if still Battery terminal shows SHORTING or Leackage than BT-Module is Faulty.

ENJOY

br
AshwaniGaur
 
@ Ashwani Gaur

Thanks again,

But Power IC is dead I think

No diode, no nothing, tracks go directly into there, and the phone has short circuit somewhere in there ..

Regards,
B
 
i'm in the same situation, custumer said that his phone was charging onely and can't be powered on, now it's totaly dead, when i mesurate curent with power adapter, there is 0mA, even if i power it on, there is no curen't, i think there is flex cable problem,
what about urs BB-GSM ?
 
Back
Top