Hi everyone. You hear this high pitched noise from you pda screen? In some cases this noise can be really distorbing.
I cannot read for a long in silence because the noise drives me crazy.
OK, so Opening my zire71 once again (i opened it at least some 100 times) i tried to look for the problem and if it is possible - to solve it.
Anyway, i do NOT recommend following these steps, consider them as demostration only. First , if your device is under warranty -
PalmOne DOES replace the units this the abovementioned defect. Also this operation is very risky, you can destroy your screen of whole
pda in second. Anyway, here's the process:
_MY_ zire looks a little bit different from inside
, but it shouldn't bother you , it's not related to the problem anyway.
OK, so let's open Zire71:
After removing the blue protective plastic it looks like this:
Next stage: - pull out the main board and unplug the cable which connects board to screen electronics.:
Well, after experimentig a little i found out that nois is NOT coming from this small pcb on the creen. I tried listening the this small pcb from
both sides. No noise. The nois is also has notheing to do with backlight. Look at the previous picture. The most left small connector - is a
backlight. After disconnecting it - noise continues as before. Nois is coming from the surface of the screen itself and almost zero at the
screen's back. So let's unplug the screen itself:
Thisi is how it looks from the side. The bottom lair - is a digitizer which registeres your taps.
The digitizer in all such Transflective screens is soft, unlike previous palm V , VX, and palm III, also other models.
After experimenting a while with digitizer i found out that if you raise a digitizer just a little bit - 1/3 of mm - the noise almost stops.
I had to experiment powering the unit in disassambled condition , which is a bit risky:
Ok, so let's eject the digitizer very carefully:
After completely removing the digitizer, the picture looks like this:
Than let's cover the screen with regular FOIL, all of the perimeter, including graffiti area.
When finished, it looks like this:
Now put the digitizer back, you can even notice, that in the left bottom corner part of foil can bee seen. Don't worry, you will not
see it in assembled state.
Let's connect the screen and check that everything is working.
Assemble the screen again, by the way, i also put foil under the small pcb - just in case...
After assembling everything back again - let's check that digitizer is working properly.
Conclusion.
To be honest, i must say, that nois is no Completely removed - but it is very silent and can be heard only when putting your ear near the
screen.
I cannot read for a long in silence because the noise drives me crazy.
OK, so Opening my zire71 once again (i opened it at least some 100 times) i tried to look for the problem and if it is possible - to solve it.
Anyway, i do NOT recommend following these steps, consider them as demostration only. First , if your device is under warranty -
PalmOne DOES replace the units this the abovementioned defect. Also this operation is very risky, you can destroy your screen of whole
pda in second. Anyway, here's the process:
_MY_ zire looks a little bit different from inside
, but it shouldn't bother you , it's not related to the problem anyway.OK, so let's open Zire71:
After removing the blue protective plastic it looks like this:
Next stage: - pull out the main board and unplug the cable which connects board to screen electronics.:
Well, after experimentig a little i found out that nois is NOT coming from this small pcb on the creen. I tried listening the this small pcb from
both sides. No noise. The nois is also has notheing to do with backlight. Look at the previous picture. The most left small connector - is a
backlight. After disconnecting it - noise continues as before. Nois is coming from the surface of the screen itself and almost zero at the
screen's back. So let's unplug the screen itself:
Thisi is how it looks from the side. The bottom lair - is a digitizer which registeres your taps.
The digitizer in all such Transflective screens is soft, unlike previous palm V , VX, and palm III, also other models.
After experimenting a while with digitizer i found out that if you raise a digitizer just a little bit - 1/3 of mm - the noise almost stops.
I had to experiment powering the unit in disassambled condition , which is a bit risky:
Ok, so let's eject the digitizer very carefully:
After completely removing the digitizer, the picture looks like this:
Than let's cover the screen with regular FOIL, all of the perimeter, including graffiti area.
When finished, it looks like this:
Now put the digitizer back, you can even notice, that in the left bottom corner part of foil can bee seen. Don't worry, you will not
see it in assembled state.
Let's connect the screen and check that everything is working.
Assemble the screen again, by the way, i also put foil under the small pcb - just in case...
After assembling everything back again - let's check that digitizer is working properly.
Conclusion.
To be honest, i must say, that nois is no Completely removed - but it is very silent and can be heard only when putting your ear near the
screen.