Help me please with SIEMENS mobiles A65 / A70

  • Thread starter Thread starter moder10
  • Start date Start date
M

moder10

Guest
Hi guys,
this is my first post....before everything i want say to you, you have done VERY GOOD WORK, i've not found nothing of similar in all the net, as forum specialized like this.

I have a little problem.
I've 2 mobiles, the siemens a65 and the a70, that are locked to an other network different from those of my country...so i've to ulock these mobiles.
I have a cruiser cable, that is recognized from my pc as : "Cruiser Team Universal Cable UC-10 (COM 11)".
I have downloaded the "Jocker Siemens EGOLD Phone Version 0.3.5.6 Inofficial ".

Is necessary the TP ?.....yes or no
Is necessary some firmware?...yes or no (if yes where i can find it)

Help me please.

Now i need to understand like making the unlock of it and than to put in practical on my mobiles thanks to your opinions and guides.

Best regards....
MODERSAT
 
first "welcome to our's forum".

Joker is good maybe best siemens tools (free)

yes, step 1 do TP, and only Recalculate All Key (Unlock). if no, fullflash.
goodluck,

salam
 
Hi friend, thanks for your welcome.
I 've understand that i have to do these things:
1- cut
2- tp
3- lunch joker (or sst)

For what regards the first point
1- cut .......... ALL OK

For the second point, i've some troubles:
2- tp (i watched the point for tp and is ok....but.......)
I would want to understand what I must put on the point for tp, red cable + or the black cable -, if i have to put cables on the battery or what... please can explain to me in particulars how do i have to do to make the testpoint? what voltage? i need one battery for the cable and an other for tp?

Please write me
 
first TP , with sst you schould cut the line , and after that phone comunicate with PC
 
yes you should cut the line with a nidle and be carefull you may use microscop it is helpfull then simply unlock thakt alll

hop your success
 
Hi guys, sorry for the late but i've not been much good.
Howewer, i have a normal COM CABLE now, i've just bought it and is arrived today.
I have done the cut on the motherboard of my siemens A65 and now i've to do the TP.
How can i do the TP?
I know that i've to put a cable on one point and the other on neutral, but how?
There's someone can make some photo to watch how to do?
Thanks a lot
and
GOOD YEAR to everyone
 
Hi,
for your information:
-cut the track (download executable from http://rapidshare.com/files/18403650/Siemens-Testpoint_Station_3.rar )
-use X55 serial service cable or C55 serial cable (see on attachemment).
-unlock with Joker (for example).
Br,
dagos
 
AH....the cable must be AUTOIGNITION???
How can i do with my cable normal bought on ebay?
I shot a photo an make here in the night...i've opened t and watched the circuit


THANKS dagos...till now, don't leave me back...help me again
 
These are the photos of my cable just opened

I wait for your opinion how to make it autoignition...even if i think making a link from the board (the point free) to jack (pin1)...write me about your opinion, if good thing to do or to avoid.
Best regards and Good WEEK END
 
Hi,
if you have C55 datacable, you don't needed to have autoignition (you need only to push shortly the red key after starting Joker - see message on the right Joker window). In attachemment you have the cable modification for autoignition). You don't needed drivers for this cable, because it is the serial cable (not USB cable). Set only com port speed to "115200" , boot typ to "normal" and enter in Service Mode.

dagos
 
OK....communication

Start...
Loading ServiceBoot...
Sending ServiceBoot Ok.
BFB Speed 115200 Baud - Ok.
HWID: 230 (A65)
A65 lg1 Sw15 23.03.05 14:06:51
IMEI: ***************xx
DisplayID: 34, Sharp Hynix HM17CM4101
Code(05): OTP closed
Code(08): BootKEY is unknown
Code(0D): Keys are registered in BCORE
Code(10): Minimal access to BFB
Code(15): Complete condition
Code(19): Monitoring is switched on
Code(1D): Blocks 5121,5122,5123 are present
Battery Voltage 3704 mV.
SecurityMode: Customer
Phone off...

I've done these steps thanks to GREAT DAGOS


Now, what do i have to do to unlock this mobile?
I've JOCKER softw
 
...it is easy
Enter in the Service Mode->ReCalc All Keys (Use Otp IMEI need to be checked) and finish! Enter again in Service Mode to verify if your phone is unlocked ( Security Mode: Factory ).
dagos
 
Start...
Loading ServiceBoot...
Sending ServiceBoot Ok.
BFB Speed 115200 Baud - Ok.
HWID: 230 (A65)
A65 lg1 Sw15 23.03.05 14:06:51
IMEI: **********************
DisplayID: 34, Sharp Hynix HM17CM4101
Code(05): OTP closed
Code(08): BootKEY is unknown
Code(0D): Keys are registered in BCORE
Code(10): Minimal access to BFB
Code(15): Complete condition
Code(19): Monitoring is switched on
Code(1D): Blocks 5121,5122,5123 are present
Battery Voltage 3709 mV.
SecurityMode: Customer
Start...
Phone off!
Loading BootsModel(A65)...
StartBoot does not answer!
Start...
Loading BootsModel(A65)...
StartBoot does not answer!
Start...
Loading BootsModel(A65)...
StartBoot does not answer!


I think someting is not OK
And now???
What do i have to do?
DAGOS... i hope in you
 
The procedure has not worked, as I can make?
I need some files to copy in the program???

do I have to format my phone?...with the instruction.....,"Del Instance"

helpppp
 
Loading BootsModel(A65)...StartBoot does not answer!that means you have not done TP correctly .i advise u to search in this forum for more info about how to make tp .bye
 
Ok, many thanks.
I control immediately the cut, then i'll try again.
Thank you ***s2060
 
Start...
Loading ServiceBoot...
Sending ServiceBoot Ok.
BFB Speed 115200 Baud - Ok.
HWID: 230 (A65)
A65 lg1 Sw07 19.10.04 14:01:52
IMEI: ************************
DisplayID: 34, Sharp Hynix HM17CM4101
Code(05): OTP closed
Code(0A): BootKEY misses in EEPROM
Code(0D): Keys are registered in BCORE
Code(10): Minimal access to BFB
Code(15): Complete condition
Code(19): Monitoring is switched on
Code(1D): Blocks 5121,5122,5123 are present
Battery Voltage 3711 mV.
SecurityMode: Customer
Start...
Phone off!
Loading BootsModel(A65)...
Sending StartBoot Ok.
Sending MainBoot Ok.
Error: SetSpeedBaud answer code 0x554355!


This the new situation after check the cut....what do i have to do?
Many thanks guys

PS.... when i'll unlock my siemens, i'll make a guide for everyone
 
Here you're OT....open a new post, and surely someone will help you to flash your mobile
 
Back
Top