You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
DYNO Numbers for Baggers???
- Thread starter Jinuine J
- Start date
Chrishaun B
New member
72.03 HP
74.44 Torque
V&H Pro Pipe, K&N Air Filter, Power Commander.
Dyno'd in Mesquite NV. 74 degrees. Numbers reflect 4th gear runs, not fifth which Im told would yeild higher bragging numbers but little else.
74.44 Torque
V&H Pro Pipe, K&N Air Filter, Power Commander.
Dyno'd in Mesquite NV. 74 degrees. Numbers reflect 4th gear runs, not fifth which Im told would yeild higher bragging numbers but little else.
real_shalom
New member
'06 Ultra with SE slip-ons, A/C and SERT, dyno'd at 1000 mile service: Max Power = 73.84; Max Torque = 75.95. Both up about 5+ from stock.
2005 Road King EFI
95" Cylinders
SE Flat Top Pistons
HDFR Heads
EVO Valves w/heavy duty springs
SE Intake
SE Quick Install Push Rods
SE High-Performance Clutch Spring
S&S 570G Gear Driven Cams
Power Commander III
Vance & Hines Oval Slip-On Mufflers w/stock header
DYNO: 94 hp.............104 fp torque................................................[sm=gears.gif]
BTW - I didn't see any 'pissing contest' starting. Where did that come from?
95" Cylinders
SE Flat Top Pistons
HDFR Heads
EVO Valves w/heavy duty springs
SE Intake
SE Quick Install Push Rods
SE High-Performance Clutch Spring
S&S 570G Gear Driven Cams
Power Commander III
Vance & Hines Oval Slip-On Mufflers w/stock header
DYNO: 94 hp.............104 fp torque................................................[sm=gears.gif]
BTW - I didn't see any 'pissing contest' starting. Where did that come from?
Força Brasil
New member
While its great these numbers are being posted, remember they are peak numbers which are great fro bragging. But with baggers its the down low torque that really matters
moonlightonalake
New member
Bruce - The intent of the thread was to post the dyno numbers to compare exhaust systems. I don't here anybody bragging. That's how pissing matches get started. You could start another thread that asks for people to post their torque numbers from idle to 3500 rpm if that's what
you want to see.
BZ
you want to see.
BZ
danikamae beroñas
New member
BZ
Never said anyone was.......after spending mucho $$$ on dyno pulls for the past 5 yrs, all I was doing was pointing out something that maybe people don't know. Afterall, someone asked how to read a graph, so not everybody is up on dyno pulls.
Btw........the best peak hp numbers will come from long open pipes. But your neighbors and local police might not like it
Nothing more.....nothing less
Never said anyone was.......after spending mucho $$$ on dyno pulls for the past 5 yrs, all I was doing was pointing out something that maybe people don't know. Afterall, someone asked how to read a graph, so not everybody is up on dyno pulls.
Btw........the best peak hp numbers will come from long open pipes. But your neighbors and local police might not like it
Nothing more.....nothing less
Blink 182 ❤
New member
Here's mine from my original flat top 95" build.
Stock heads cams and ignition,just Hooker slip ons on stock head pipes a Mikuni HSR 42 and SE breather.
I should have my bike back next week from upgrades to 95" +.010 10.25 cast pistons,Baisley superstock heads,S&S geardrive 570 cams,Dyna ignition and Rinehart true dual exhaust.
They are doing a Dyno break in to seat the rings and tune the bike so I'll have a new dyno chart to put up here then.
Y2K[8D]
Stock heads cams and ignition,just Hooker slip ons on stock head pipes a Mikuni HSR 42 and SE breather.
I should have my bike back next week from upgrades to 95" +.010 10.25 cast pistons,Baisley superstock heads,S&S geardrive 570 cams,Dyna ignition and Rinehart true dual exhaust.
They are doing a Dyno break in to seat the rings and tune the bike so I'll have a new dyno chart to put up here then.
Y2K[8D]
krazy4twilight31
New member
Was at the dyno shop yesterday to witness a run. A completely stock appearing '05 black Electra Glide Standard (other than a velocity stack and compression releases). Must have had SOME internal work..... cause it showed.....146 HP.....on the screen. WOW, that was impressive. I thought the dyno chamber was going to explode!