Pregnant With #1!
New member
You can chech it simply with meter
First higher point is Gnd....
First higher point is Gnd....
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
All cable's pinouts for chines Mobiles
- Thread starter Pregnant With #1!
- Start date
hondafmxfan
New member
Sorry Thats a wrong post
i am so peng its unreal!
New member
[No message]
Helena! :)
New member
Complete PINOUT IFOE P168+ (Cect P168+):
I looked for serial cables for sale for this phone, and the models they supported, with this models I searched pinout, looked at my USB pinouts with a tester(to know my USB pinout) and the pinout of my PTT microphone auriculars, and i found this that matches all of them so this one should be the complete pinout of the phone(JC_BY Thanks for your help):
PINOUT FOR IFOE P168+ (Cect P168+ ?) and... GStar-GM328 and Samsung-D900
Connector_2x6_mini
/ 1 2 3 4 5 6 \
| 7 8 9 10 11 12 |
1: HF ear
2: Gnd
3: +Vcc
4:
5: Tx
6: USB D-
7: HF ear
8: HF mic
9: +Vcc
10: +Battery
11: Rx
12: USB D+
Please post firmware if you find it for this phone!
And i have a problem, i DISABLED the engineering mode by pressing *#6810#
DONT DO IT! AND PLEASE TELL ME HOW TO RECOVER THE ENGINEERING MODE, IM SURE THERES A CODE FOR THAT!
HELP!!
I looked for serial cables for sale for this phone, and the models they supported, with this models I searched pinout, looked at my USB pinouts with a tester(to know my USB pinout) and the pinout of my PTT microphone auriculars, and i found this that matches all of them so this one should be the complete pinout of the phone(JC_BY Thanks for your help):
PINOUT FOR IFOE P168+ (Cect P168+ ?) and... GStar-GM328 and Samsung-D900
Connector_2x6_mini
/ 1 2 3 4 5 6 \
| 7 8 9 10 11 12 |
1: HF ear
2: Gnd
3: +Vcc
4:
5: Tx
6: USB D-
7: HF ear
8: HF mic
9: +Vcc
10: +Battery
11: Rx
12: USB D+
Please post firmware if you find it for this phone!
And i have a problem, i DISABLED the engineering mode by pressing *#6810#
DONT DO IT! AND PLEASE TELL ME HOW TO RECOVER THE ENGINEERING MODE, IM SURE THERES A CODE FOR THAT!
HELP!!
hearts_rsweet
New member
the picter is a bit different from my phone.mine has only 3 circles, any other picture?
Sarah-Jane
New member
hi help any sol. to unlock zte g420 gota pinout
iamtheraingoddess
New member
Dear "jamohaki" you should show here the picture of your phone(board's pins)
regards
regards
Ryan Rivera
New member
Try this code *#110*01# for Engenieering Mode....
and show the result
regards
and show the result
regards
Yes, i tryed this one too, didnt work.
The problem is that i made a mistake: I changed PS to USB (instead of UART, using the the code *#3646633#, that worked great to enter enginnering menu) and latter entered a dangerous code: *#6810# that DISABLED THE ENGINEERING MENU and several other codes. The question is:
HOW CAN I CHANGE THE PS TO UART without entering the engineering mode? Is there a way to do that? To change to UART or to revert this bad code so i can use the Engineering menu.
I've reseted the phone, entered all the codes i have found but nothing happened, and searched the forum for two days.
If you could help me Skybird I would be very glad, so i continue investigating ways to modify my phone. Thanks in advance.
Regards, Robert.
The problem is that i made a mistake: I changed PS to USB (instead of UART, using the the code *#3646633#, that worked great to enter enginnering menu) and latter entered a dangerous code: *#6810# that DISABLED THE ENGINEERING MENU and several other codes. The question is:
HOW CAN I CHANGE THE PS TO UART without entering the engineering mode? Is there a way to do that? To change to UART or to revert this bad code so i can use the Engineering menu.
I've reseted the phone, entered all the codes i have found but nothing happened, and searched the forum for two days.
If you could help me Skybird I would be very glad, so i continue investigating ways to modify my phone. Thanks in advance.
Regards, Robert.